quick start guide - ISOGO

1 downloads 294 Views 1MB Size Report
and adjust until all slack is removed from top tether. • Remove ISOGO lower connector from the mesh pocket (Euro), or
QUICK START GUIDE forward-facing installation

3. Tighten the connector straps

I. Select the desired seat angle

• Start with the strap on the inside closest to the centre and remove as much slack out as possible, then move to the outside strap and remove as much slack as possible.

• Push the red button, located on the front of the base, inwards to select the desired seat angle: ‘LOW’, ‘MID’ or ‘HIGH’. • Place the car seat in the vehicle, facing forward.

• Alternate removing the slack from side to side until you get a firm fitment and achieve a GREEN indication (Figure D).

2. Attaching ISOGO lower connectors • Remove ISOGO lower connector from the mesh pocket (Euro), or from underneath the side wings of the cover (Hera).

tip: Always check for GREEN at eye level.

PUSH

FIGURE B

CLICK!

& PULL

• Ensure to pull loose end parallel to the belt strap (Figure E). A good technique is to pull upwards in the direction of the belt then push inwards (in the same motion) towards the centre of the seat (through the rearward facing belt path hole).

PULL

PUSH

+

FIGURE A

• Locate low anchorage points. You can find this by looking for the ISOFIX logo located on the vehicle seat (Figure B). • Attach the lower connector on both sides (Figure C). Listen for a “click!”

FIGURE D

FIGURE E

+

• Release belt to full length by pressing grey button and pulling adjustor (Figure A). Repeat for both sides.

Euro & Hera

4. Attach top tether strap • Attach the top tether strap to the top anchorage point in the vehicle (Figure F).

BOTH SIDES

tip: You can move the car seat out of the way to locate and attach the connectors, then place back into position before tightening.

FIGURE C

• Ensure there are no twists in the belt, and adjust until all slack is removed from top tether.

FIGURE F

QUICK START GUIDE

rearward-facing installation 4. Tighten the connector straps

2. Place the car seat in the vehicle

• Alternate removing the slack from side to side until you get a firm fitment and achieve a GREEN indication (Figure E).

• Flip the stabilizing bar up from the base and into position (Figure A).

tip: Always check for GREEN at eye level.

FIGURE A

3. Attaching ISOGO lower connectors • Remove ISOGO lower connector from the mesh pocket (Euro), or from underneath the side wings of the cover (Hera).

PUSH

FIGURE B

& PULL

PULL

FIGURE E

PUSH

• Ensure to pull loose end parallel to the belt strap (Figure F). A good technique is to pull upwards in the direction of the belt then push inwards (in the same motion) towards the centre of the seat (through the rearward facing belt FIGURE F path hole).

5. Attach top tether strap • Attach the top tether strap to the top anchorage point in the vehicle (Figure G).

• Locate low anchorage points. You can find this by looking for the ISOFIX logo located on the vehicle seat (Figure C). • Attach the lower connector on both sides (Figure D). Listen for a “click!”

• Start with the strap on the inside closest to the centre and remove as much slack out as possible, then move to the outside strap and remove as much slack as possible.

+

• Push the red button, located on the front of the base, inwards and raise seat into ‘HIGH’ position.

+

I. Place the seat in the highest recline position

• Release belt to full length by pressing grey button and pulling adjustor (Figure B). Repeat for both sides.

Euro & Hera

FIGURE C

• Ensure there are no twists in the belt, and adjust until all slack is removed from top tether.

FIGURE G

CLICK!

INSIDE

BOTH SIDES

tip: You can move the car seat out of the way to locate and attach the connectors, then place back into position before tightening.

FIGURE D

tip: In the rearward-facing position, the top tether adjustor will appear as though it is facing inwards (as shown in Figure H). This is correct.

FIGURE H