Image Sensors for Video and User Interface ... - ON Semiconductor

AUDIO/VIDEO/TOUCH

Image Sensors for Video and User Interface Communications Devices

Key Features

• Drones • VR/AR headsets • Webcams and WiFi cameras • Depth sensing cameras • 360° and home security cameras

Applications

• HD to 18 Megapixel • HD, FHD, 4K video • Color, monochromatic • High performance in low light conditions • Single sensor and stereo configurations

• Streaming video • Home monitoring • Gesture control • Touchless control for gaming • Body motion tracking and scene analytics Device MT9M114 AR0130 AR0135CS AR0141CS AR0144CS AS0260 AR0261 AR0237/AR0238 AR0239 AR0330 AR0430 AR0521 AR1335 AR01820

Description

Resolution (MP)

Frame Rate (fps)

1/6" System-on-Chip 1.9 µm BSI pixel color

1.3 (720P)

30

1/3" CMOS Image Sensor 3.75 µm pixel color monochrome 1/3" Global Shutter CMOS Image Sensor 3.75 µm pixel color monochrome 1/4" CMOS Image Sensor 3.0 µm pixel color monochrome 1/4" Global Shutter CMOS Image Sensor 3.0 µm pixel color monochrome 1/6" CMOS Image Sensor System-on-Chip 1.4 µm pixel color 1/6" CMOS Imaging Sensor 1.4 µm BSI pixel color 1/2.7-Inch Full HD Digital Image Sensor 3.0 µm pixel color RGB-IR 1/2.7-Inch Full HD Digital Image Sensor 3.0 µm BSI pixel color 1/3" CMOS Imaging Sensor 2.2 µm pixel color 1/3.1" CMOS Imaging Sensor 2.0 µm BSI pixel color depth 1/2.5" CMOS Imaging Sensor 2.2 µm BSI pixel color monochrome 1/3.1" CMOS Imaging Sensor 1.1 µm BSI pixel color monochrome 1/2.3" CMOS Imaging Sensor 1.25 µm BSI pixel color

1.2 (720P) 1.2 (720P) 1 (720P) 1 (720P) 2 (1080P) 2 (1080P) 2.1 (1080P) 2.3 (1080P) 3.5 4 5 13 18

45 54 60 60 30 60 60 60 60 120 60 13MP 30, 4K2K 30, 1080P 60 18MP 24fps, 1080P 120

USB HDMI WiFi

Module Image Processor

Sensor

Sensor

Page 2

Consumer Electronics Solutions

Features • Design flexibility/customization (i.e., EEPROM if desired for trimming) • 0.0125 lux detection with customizable filtering (i.e., Photopic Light Response) • Dark current and temperature compensation • Lowest power consumption per resolution bit • I2C Interface (including High Speed Mode) and no effect on bus during power down Voltage Supply

Vin = 3.3 V hν

1k VDD

16-Bit ADC

Voltage Supply

0.1 μF

SCL

I2C Bus

SD

LV0104CS

LED Drivers

MCU

LEDs

SCL

When the Sunlight is Strong, Extending the Dynamic Range by Lowering Gain

VCC

SW CPU 0.1 μF

Control Logic

SDA

SDA Ambient Light 1 μF Sensor VSS SCL

VCC

Approximates Human Eye Response

1k

Amp

OUT

Gain Cont.

I/O

CPU

ADC

Current-Voltage Conversion

Simple 2-Wire I2C Interface

LA0151CS GND

GND

Special Features

IO Typ @ E V = 100 Lux (mA)

Output Interface

Vin Range (V)

TA Range (°C)

Package

LA0151CS

2-Stage Gain Switching

8 (high gain)

Analog, linear current

2.2 - 5.5

-30 to +85

ODCSP-4

LV0104CS

Integrated Sleep Mode

—

I2C, 16-bit ADC

2.3 - 3.6

-30 to +85

ODCSP-4

LV0111CF

Standby Function

21

Analog, logarithmic current

2.3 - 5.5

-30 to +85

ODCSP-4J

NOA1212

Dark Current Compensation

51 (high gain)

Analog, linear current

2.0 - 5.5

-40 to +85

CUDFN-6

NOA1213


—

Analog

2.0 - 5.5

-40 to +85

CUDFN-6

NOA1305


—

I2C, 16-bit ADC

2.4 - 3.6

-40 to +85

CUDFN-6

Device

ON Semiconductor

Page 3

AUDIO/VIDEO/TOUCH

Ambient Light & Proximity Sensors

AUDIO/VIDEO/TOUCH

Closed Auto-Focus Drivers LC898217XC/XH closed loop auto focus driver includes integrated driver, loop digital filter, and EEPROM. System implementation requires only a Hall sensor and by-pass condenser. LC898217XC/XH enables fast and accurate auto focusing, with low power consumption, from an extremely small footprint.

Key Features • Integrated equalizer circuit • Integrated EEPROM memory (128 byte) • Integrated OSC, LDO, and Hall amplifier • Integrated Constant Current Driver and Linear Compensation • 1-channel, 11-bit ADC; 2-channel, 8-bit DAC

OSC

LDO

I2C IF

EEPROM

DA Hall Sensor

Hall Amp

Constant Current Driver

DA

Equalizer

AD

Control Logic

LC898217XC/XH Block Diagram

Type

VDD Min (V)

LC898214XD

Feedback

LC898217XC/XH

Feedback

Device

Page 4

VDD Max (V)

VM Min (V)

VM Max (V)

Driver (mA)

CPU IF

D/A

A/D

2.6

3.6

—

—

120

I2C

8-Bit

10-Bit

WLCSP-8

2.6

3.3

—

—

110

I2C

8-Bit

11-Bit

WLCSP-10

Package(s)


LC898123F40 DSP-based Optical Image Stabilization (OIS) and Auto Focus (AF) controller/driver includes integrated Flash memory, analog circuits, H-bridge and constant current drivers. The integrated Flash enables fast wakeup and simplifies Host-side software implementation.

Key Features • Integrated DSP software filter • Integrated Flash memory (40 KB) • Integrated OSC, LDO, and Hall amplifier • Digital Gyro I/F • 4-channel, 14-bit ADC; 3-channel, 8-bit DAC

I2C IF

OSC

H-Bridge Const Current for AF

D-Gyro IF

H-Bridge Const Current for OIS

Flash (40 KBytes)

DA

Control Logic Position Sensor

AD

DSP

PWM Logic

LC898123F40 Block Diagram

Type

VDD Min (V)

LC898123AXD

Feedback

LC898123F40

Feedback

Device

ON Semiconductor

VDD Max (V)

VM Min (V)

2.6

3.6

2.6

2.6

3.3

2.6

VM Max (V)

Driver (mA)

CPU IF

D/A

A/D

Package(s)

3.6

195/120

I2C

8-Bit

12-Bit

WLCSP-35

3.3

200/150

I2C

8-Bit

14-Bit

WLCSP-35

Page 5

AUDIO/VIDEO/TOUCH

Optical Image Stabilization Drivers

AUDIO/VIDEO/TOUCH

Amplification for Video Signals Input Video Signal Detection

VCC 10

NCS2584

Shutdown Detection Cvbs IN 1

Transparent Clamp 8 MHz,

HD IN1 2

6th

HD IN2 3

9 Cvbs OUT

6 dB

8 HD OUT1

6 dB

7 HD OUT2

6 dB

6 HD OUT3

Order

Transparent Clamp 34 MHz,

6 dB

6th

Order

Transparent Clamp 34 MHz, 6th Order

HD IN3 4

Transparent Clamp 34 MHz, 6th Order Output Load Detection 5

GND

Detect if TV Is Plugged

Video Amplifiers Channels

GBW Typ (MHz)

VCC Max (V)

Package

NCS2566

6

8/34

5

TSSOP-20

NCS2564

4

8/34

5

TSSOP-14

NCS2584

4

8/34

3.3

TSSOP-14

NCS2563

3

30

5

SOIC-8

NCS2553

3

8

5

SOIC-8

NCS2561

1

8

3.3

SC-70

NE592x8

1

40

8

SOIC-8, PDIP-8

NE592x14

1

90

8

SOIC-14, PDIP-14

Device

Page 6


LC898302A

LC898301

The LC898302A is a haptic driver able to drive LRA and ERM. The drive frequency is automatically adjusted to the resonance frequency of the linear vibrator without external components.

The LC898301 is an extended supply range version of the LC898300 LRA driver, compatible with cellular battery voltage. The architecture chosen enables strong vibration in minimal board space. Moreover, the LC898301 exhibits superior vibration performance.

Unique Features • Drive LRAs with automatic tuning and breaking • Drive ERM; drive voltage controlled via PWM Other Features • Supply voltage = +2.7 to +5.5 V • Iout max = 200 mA • Bridge RDS(on) = 2 x 2 W (4 x 2 W MOSFETs embedded) • Low standby current Benefits • High efficiency • Easy handling (no adjustment for any LRA) • Strong vibration Device LC898302A

Description

Package

Haptic Driver for LRA and ERM

WLCSP-6

Other Features • Supply voltage = +3.0 to +5.5 V • Iout max = 200 mA • Bridge RDS(on) = 2 x 2 W (4 x 2 W MOSFETs embedded) • No peripheral component required (only 0.1 µF cap) • Low power consumption Benefits • High efficiency • Easy handling (no adjustment for any LRA) • Strong vibration

VDD (2.7 to 4.5 V) LDO

Unique Features • Automatically adjust driving frequency (ON Semiconductor patent) • Minimized start-up and brake period (Quick stop) • Automatically stop braking to avert counter vibration

• Fault-detection • Battery direct supply • Fully configurable through I2C

POR H-Bridge Driver

PWM Drive Signal Generator

OUT1 OUT2

Device LRA ERM

Description

Package

LC898301XA

Haptic Driver for LRA

WLCSP-8

LC898301AXA

Haptic Driver for LRA with Immersion System

WLCSP-8

MODE OSC

VDD (3.0-5.5 V)

TSD DVDD (1.8 V)

VSS

LDO

Block Diagram EN

SCL SDA

Drive Signal Generator

H-Bridge with Power Control

Register Setting

OSC

OUT1 OUT2

Linear Vibrator

RSTB VSS

Block Diagram

ON Semiconductor

Page 7

AUDIO/VIDEO/TOUCH

Haptic Drivers

AUDIO/VIDEO/TOUCH

Capacitive Touch Sensors Design-Friendly, Low-Cost Operation, High Reliability

• Adhesive free



• Long sensor trace

   

• Wide range operational temperature • No extra components • High noise immunity

• Reduce manufacturing cost and improve reliability by eliminating existing adhesive process • Provide flexible PCB design • Available in high-temperature environment • Reduce BOM • Improve stability and reliability

Door Phone

Light Switch

Control Panel

Page 8


LC717A devices are high performance, cost-effective, and highly usable capacitance converters, for use in touch switch applications. They have 8 or 16 channel capacitance-sensor inputs, and can replace mechanical switches. In particular, the LC717A30UJ has superior sensitivity performance, so it can detect both hands wearing multiple layers of gloves and hands with 15 cm of distance. In addition, it can perform gesture detection. Features • Differential capacitive detection using mutual capacitance • Capacitance detection down to femtofarad level • High sensibility performance • High adaptability — calibration function, noise reduction, wide range temperature operation • Design friendly — adhesive free, various circuit board design, minimal external components

Proximity/Gesture Sensing (cm)

Sensing Inputs

Sensing Outputs

Interface Control

VDD (V)

Package

LC717A00AJ

0-10

8

8

SPI / I2C

2.6 - 5.5

SSOP-30

LC717A00AR

0-10

8

8

SPI / I2C

2.6 - 5.5

VCT-28

LC717A10AJ/PJ

0-10

16

0

SPI / I2C

2.6 - 5.5

SSOP-30

LC717A10AR

0-10

16

0

SPI / I2C

2.6 - 5.5

VCT-28

LC717A30UJ

0-20

8

0

SPI / I2C

2.6 - 5.5

SSOP-30

Device

LC717A00AR Evaluation Kit

ON Semiconductor

LC717A30UJ Evaluation Kit

Page 9

AUDIO/VIDEO/TOUCH

Capacitive Touch Sensors

AUDIO/VIDEO/TOUCH

Portable Sound Solution ASSP LC823450 series high resolution, ultra-low power portable audio system solution Key Features • Ultra low power consumption • Integrated 1656 KByte SRAM • Arm® Cortex®-M3 Dual Core • Proprietary 32-bit DSP Core (LPDSP32) • DSP audio code available for MP3 codec, FLAC codec, Noise Cancel, Zoom Mic • High resolution 32-bit & 192 KHz audio processing capability

• Integrated analog blocks for low-power Class D HP amplifier, system PLL, dedicated audio PLL • Hard wired audio functions for MP3 encoder and decoder, EQ (6-band equalizer), ASRC (Asynchronous Sample Rate Converter) • Integrated interfaces for USB2.0 HS device or host (not OTG), eMMC, SD card I/F • ASRC with jitter hiding function, DSP code for SBC/AAC, UART with DMA & FIFO support for low power Bluetooth® audio

JTAG (LPDSP) Sys PLL 20 MHz (1-50 MHz)

OSC Aud PLL

I2C ADDA 2ch/2ch

PCM 2ch D-AMP 2ch

Key

10-bit ADC 6ch

Small LCD

SPI

S-Flash (Quad)

SF(QSPI) w/ Cache

Battery

32.768 kHz

Design Focus

LC823450TA

Voice Recorder

LC823450XC

Wearable

LC823450XD

High End

Page 10

Arm® Cortex®-M3

Arm® Cortex®-M3

ROM 258 KByte

RAM 1.5 MByte

Audio Engine

PCM 2ch

ADDA 2ch/2ch

Device

RC OSC

RTC

Frequency (MHz) 160 @ 1.2 V Typ 100 @ 1.0 V Typ 160 @ 1.2 V Typ 100 @ 1.0 V Typ 160 @ 1.2 V Typ 100 @ 1.0 V Typ

H/W • MP3 Encoder • MP3 Decoder

SSRC, ASRC, EQ, etc.

USB2.0 Host or Device XMC(2CS) and LCD

or

8/16bit

NOR SRAM

8bit

Color LCD

UART

I2C Multiple Timer 2ch * 4

SDRAM eMMC

eMMC SD/MS SD

UART 2ch

DMA 8ch

RAM (KByte)

(M3)

SDRAMC (1CS)

S/W (LPDSP32) • WMA Decoder • AAC Decoder • Noise Cancel, etc.

Plain Timer (w/ WDT) 1ch * 3

SWD or SWV

GPcIO 90ch

ARM Cortex-M3 SD Card I/F Cores Channels

SD/MS WiFi Module, etc. Bluetooth w/ CTS, HCI Module RTS

SW etc

Features

Package

1656

Single

3

Class D HP Amplifier

TQFP-128L

1656

Single

2

External LCD I/F (8-bit)

WLCSP-154

1656

Dual

3

Class D HP Amplifier; External LCD I/F (8-bit); HW MP3 Encoder

WLCSP-154


AUDIO/VIDEO/TOUCH

Portable Sound Solution ASSP Ultra Low Power • Over 120 hours playback with 2 x AAA battery (70% longer than popular portable music players) • Advanced power management technology • 4.8 mA @ 128 Kbps by MP3 hardware decoding • 0.11 mW/MHz @ 1.0 V while Cortex®-M3 Single Core operation • Integrated low power D class amplifier

Small Footprint Sys PLL 20 MHz (1-50 MHz)

OSC Aud PLL

ADDA 2ch/2ch

PCM 2ch I2C

ADDA 2ch/2ch

PCM 2ch D-AMP 2ch

Key

10-bit ADC 6ch

Small LCD

SPI

S-Flash (Quad)

SF(QSPI) w/ Cache

Battery

32.768 kHz

RTC

RC OSC ARM® Cortex®-M3

ARM® Cortex®-M3

ROM 258 KByte

RAM 1.5 MByte

Audio Engine H/W • MP3 Encoder • MP3 Decoder

(M3) USB2.0 Host or Device XMC(2CS) and LCD

or

8/16bit

NOR SRAM

8bit

Color LCD

SDRAMC (1CS)

S/W (LPDSP32) • WMA Decoder • AAC Decoder • Noise Cancel, etc. SSRC, ASRC, EQ, etc.

UART

I2C Multiple Timer 2ch * 4

GPcIO 90ch

5.52 mm

SDRAM eMMC

eMMC SD/MS SD

UART 2ch

DMA 8ch Plain Timer (w/ WDT) 1ch * 3

SWD or SWV

SD/MS

5.33 mm

JTAG (LPDSP)

WiFi Module, etc. Bluetooth w/ CTS, HCI Module RTS

SW etc

• 5.52 mm x 5.33 mm WLCSP-154 suitable for portable, wearable audio • Highly integrated SoC (CPU+DSP+AUDIO) • Hi-Resolution Recording/Playback capability • Cortex®-M3 dual core • Proprietary 32-bit DSP (LPDSP32) • 1656 Kbyte internal SRAM

Turn Key Software Support • Suitable for portable, wearable digital music • Support wireless synchronized stereo playback

Application Layer

Middleware Layer

System APF

✘

IPL2APP

✘

IPL

✔

EVT MD

✔

STG MD

✔

AUD MD

✔

SYS MD

✔

USB MD

✔

✔

✘ BT Protocol Stack

Library

Common

✔

APL DR

✘

File System

✔

SD/eMMC Driver

✔

Timer Driver

✔

MTM Driver

✔

SFC Driver

✔

INTC Driver

✔

UARTDR

✔

SPI Driver

✔

Audio Driver

✔

DSP Loader

✔

SDIO Driver

✘

DSP Lib

✔ OS

AD Converter ✔ Driver

RTC Driver

✔

USB Driver

✔

I2C Driver

✔

IO EXP

✘

Driver

CODEC Driver ✘

Power Driver ✔

H/W

ON Semiconductor

✔

MP Ready

✘

User Depending

Reference Code Internal ROM Further Discussion Needed

Provide C Source Code Provide Library or Binary Code Sample Application May Not Use

Page 11

AUDIO/VIDEO/TOUCH

Portable Sound Solution ASSP Evaluation Kit The LC823450XGEVK is an audio processing system Evaluation Kit used to demonstrate the LC823450. This part can record and playback, and offers high-resolution 32-bit & 192 kHz audio processing capability. It is possible to cover most of the functions necessary for portable audio with only this LSI. It has Dual CPU and DSP with high processing capability, and internal 1656K-Byte SRAM, which make it possible to implement large scale program. And it has integrated analog functions (low-power Class D HP amplifier, PLL, ADC etc.) so that PCB space and cost can be reduced, and it has various interface (USB, SD, SPI, UART, etc.) to make extensibility high. Also it is provided with various function including SBC/AAC codec by DSP and UART and ASRC (Asynchronous Sample Rate Converter) for Bluetooth audio. Low power consumption makes it suitable for portable audio devices, such as wireless headsets.

9

11 12

4

5

LC823450 Audio CODEC USB Connector Serial Flash eMMC Switches microSD LCD

Radio Frequency

24-bit

LC823450

CODEC

Line IN

Head Phone

7

Power Supply Control Measurement

Switch

USB

LCD

SWD−IF

UART

I/O

LC823450XGEVK Block Diagram 16

3 1 2 3 4 5 6 7 8

eMMC

6

2

15

microSD

Digital-Mic IN

D-class AMP Output

1

14

Serial Flash

Bluetooth®

8

13

Audio

Memory

10

9 10 11 12 13 14 15 16

Bluetooth®

16

UART Connector Power Supply Control Digital Mic ICE Connector Headphone Line Input LEDs

Key Features • File Transfer Connecting to PC with USB • MP3 Recording with USB Bus Power Supply • MP3 Playback with USB Bus Power Supply

• Measurement of Current Consumption

LC823450XGEVK Evaluation Board

Page 12


VCC = +15 V VEE = −15 V TA = 25°C

50 30 20 10

5.0 3.0 2.0 1.0

Current 5.0

0.5 Voltage

3.0 2.0

n

AUDIO/VIDEO/TOUCH

10

100

1.0 1.0

10

100 1K f, FREQUENCY (Hz)

10K

0.3 0.2 0.1 100K

n

nV/ √ Hz

Amplification and Buffering for Audio Signals

MC33077 Input Referred Noise Voltage and Current vs Frequency

Key Features • Low noise • Fast response times • Single, dual and quad devices Low Noise Operational Amplifiers Channels

Noise Typ (nV/√Hz)

GBW Typ (MHz)

SR Typ (V/ms)

Package

LM833

2

4.5

15

7

SOIC-8, PDIP-8

MC33077

2

4.4

37

11

SOIC-8, PDIP-8

MC33078

2

4.5

16

7

SOIC-8, PDIP-8

MC33079

4

4.5

16

7

SOIC-14, PDIP-14

MC33178

2

7.5

5

2

Micro8, SOIC-8, PDIP-8

MC33179

4

7.5

5

2

TSSOP-14, SOIC-14, PDIP-14

MC33272A

2

18.0

24

10

SOIC-8, PDIP-8

MC33274A

4

18.0

24

10

SOIC-14, PDIP-14

NE5532

2

5.0

10

9

SOIC-8, PDIP-8

NE5534

1

4.0

10

13

SOIC-8, PDIP-8

Device

ON Semiconductor

Page 13

AUDIO/VIDEO/TOUCH

Low Resistance Switching for Audio Signals

NLAS2750

1.8mm

Op Amp Audio Out

1.4mm

Analog Switch

0.55mm One µDFN-10

Audio Switches Device

Description

Channels

RON Max (W)

Package

NLAS5157

Single SPDT

1

0.5

mDFN-6

FSA2275/6

DPDT with Negative Swing

2

0.5

UQFN-12

FSA551

Dual SPST

2

0.6

WLCSP-9

FSA553

Dual SPST

2

0.8

WLCSP-9

NLAS2750

Dual SPDT with Negative Swing

2

0.6

mQFN-10

NLAS5223C

Dual SPDT

2

0.5

mQFN-10

FSA550

Single 4PST

4

0.8 Typ

WLCSP-12

NLAS3799B

Dual DPDT

4

0.5

mQFN-16

Key Performance Characteristics • Excellent Audio Fidelity - Very Low THD, 0.011% Typical • Wide 1.65 - 4.5 V Power Supply Range • Extended Temperature Capable • Low RDS(on), Tight Channel Matching

Page 14


AUDIO/VIDEO/TOUCH

Audio Filters – RC & LC EMI Filters with ESD Protection Key Features • ESD protection exceeds 8 kV contact (IEC 61000-4-2) • Matched inductors and capacitors • Lowest insertion loss, critical for analog signals • Excellent filtering performance across all wireless bands • Integrates large scale capacitive elements with resistors or inductors to create excellent noise attenuation starting at 22 MHz 0 -10 Discrete Implementation

Gain (dB)

-20 -30 -40 -50

Integrated Filter Response

-60 -70 1.E+05

1.E+06

1.E+07 1.E+08 Frequency (Hz)

1.E+09

1.E+10

Audio Filters Type

Lines

f3 dB (MHz)

Attenuation (-dB @ 1 GHz)

IEC 61000 (kV)

Package

2 Line Audio EMI Filter with ESD Protection

RC

2

50

-35

30

DFN-8

NUF2441

Integrated Passive Filter with ESD Protection

LC

2

25

-35

8

FlipChip-6

NUF2450

2 Line EMI Filter with ESD Protection

LC

2

20

-40

20

µDFN-8

NUF4220

4 Line Audio EMI Filter with ESD Protection

LC

4

16

-38

18

DFN-8

Device

Description

NUF2114

ON Semiconductor

Page 15

MJx1302A (PNP) and MJx3281A (NPN) Gain Linearity 1000 hFE, DC Current Gain

AUDIO/VIDEO/TOUCH

Audio Transistors for Superior Linearity and Gain Matching Device Number

PNP NPN

NPN

PNP

NJW0281

NJW0302

100°C

100 -25°C

10 0.1

25°C

1.0 IC, Collector Current (A)

Closely matched complementary pairs assure symmetrical performance while minimizing manual gain sorting

PD IC @ 25°C VCEO Max (W) (V) (A)

hFE Min/ Max

@ IC f T (A) (MHz) Package

50

150

8

20 min

4

30

TO-3P

MJW3281A MJW1302A

200

260

15

75/150

5

30

TO-247

MJL3281A MJL1302A

200

260

15

75/150

5

30

TO-264

NJW3281

200

260

15

75/150

5

30

TO-3P

NJW1302

10

Excellent gain linearity for accurate reproduction of input signal

260 V Capability for Greater Dynamic Range

Power Bipolar Audio Output Transistors RMS Power Output Up to 50 W

50 to 180 W

180 to 200 W

> 200 W

Page 16

NPN MJE15030 MJE15032 MJE15034 NJW44H11 MJ15003 NJW0281 MJ15015 MJL21196 MJW21194 MJW21196 MJL21194 MJW3281A MJL3281A NJW3281 MJ15024 MJ21194

PNP MJE15031 MJE15033 MJE15035 — MJ15004 NJW0302 MJ15016 MJL21195 MJW21193 MJW21195 MJL21193 MJW1302A MJL1302A NJW1302 MJ15025 MJ21193

PD @ 25°C (W) 50 50 50 120 150 150 180 200 200 200 200 200 200 200 250 250

VCEO (V) 150 250 350 80 140 260 120 200 250 250 250 260 260 260 250 250

IC Max (A) 8 8 4 10 20 15 15 16 16 16 16 15 15 15 16 16

hFE Min/Max 20 min 50 min 50 min 100/400 25/150 75/150 20/70 25/75 20/60 25/60 25/75 75/150 75/150 75/150 15/60 25/75

@ IC (A) 4 1 1 2 5 3 4 8 8 8 8 5 5 5 8 8

f T Typ (MHz) 30 30 30 85 3 30 3 4 4 4 4 30 30 30 4 4

Package TO-220 TO-220 TO-220 TO-3P TO-3 TO-3P TO-3 TO-264 TO-247 TO-247 TO-264 TO-247 TO-264 TO-3P TO-3 TO-3


AUDIO/VIDEO/TOUCH

ThermalTrak™ Output Transistors Eliminate Thermal Lag and Improve Fidelity 1.00 kΩ

100 Ω

1N4148

1N4148

1.00 kΩ

1.00 kΩ

1N4148

10 pF

150 pF

NJL3281D

150 pF

MPSA06

MPSA56

NJL3281D

NJL3281D

100 Ω 1N4148

Input

1.00 kΩ

10.0 kΩ

10 pF

MJE15032

MPSA56

Eliminates 4 components, including trimpot

MPSA06

MPSA06

47.5 Ω

47.5 Ω

274 Ω +

100 Ω

0.1 Ω

0.1 Ω

0.1 Ω

274 Ω

Output 100 Ω

10 pF

0.1 Ω

0.1 Ω

5.6 Ω

0.1 Ω

MPSA56

10.0 kΩ

MPSA06 +

TO-264

100 nF

100 Ω MJE15033

1.0 kΩ

ThermalTrak™

150 pF

1N4148

100 μF-POL 1.00 kΩ

100 Ω

NJL1302D

10.0 kΩ 100 kΩ

NJL1302D

NJL1302D

Bias diodes incorporated into output devices eliminates the need for complex bias control circuitry.

Vastly improves bias stability and helps eliminate thermal shock Audio Amplifier Performance

Standard Industry Design vs. ThermalTrak™ Solution 100

Distortion (%)

50 20

Color

Data

Comment

10

Green

Anlr.THD+N Ratio

10 KHz no load Tr. bias

5

Red

Anlr.THD+N Ratio

10 KHz no load diode bias

2 1 0.5 0.2

Before

0.1 0.05 0.02 0.01 0.005

After

0.002 0.0008 10m

20m

50m

100m

200m

1

500m

2

5

10

20

40

Voltage

Device Number

PD @ 25°C VCEO (W) (V)

NPN

PNP

NJL0281D

NJL0302D

180

NJL3281D

NJL1302D

200

ON Semiconductor

hFE

IC Max (A)

Min/Max

@ IC (A)

fT (MHz) Package

260

15

75/150

3

30

TO-264-5

260

15

75/150

7

30

TO-264-5

Page 17

General and LCD MCUs MCU Features • Pins: • ROM: • RAM: • ADC:

10 – 100 4 – 768 KBytes 256 – 48,640 Bytes 3 – 16 channels

ROM RAM (kByte) (Byte)

CONTROL

Device

Type

LC87FBG08A

8-bit General

8

256

LC87FBK08A

8-bit General

8

LC87FBL08A

8-bit General

8

LC87FBH08A

8-bit General

LC87F2R04A

8-bit General

LC87BK08A* LC87F2416A

• Operation Voltage: 1.8 – 5.5 (V) • Stand-by IDD: 0.02 µA • RTC (Clock) IDD: 0.45 µA (with low power model)

μA

I/Os

PWMs

UARTs

ADC

LVD

POR

Features

Package

21

2

1

12/8-bit x 9ch

✔

✔

High accuracy internal OSC (±2.0%); all operation is minimum 1.8 V

SSOP-24, VCT-24

256

21

2

—

12/8-bit x 8ch

✔

✔

High accuracy internal OSC (±3.0%); Support Mask Type

SSOP-24

256

26

2

—

12/8-bit x 11ch

✔

✔

High accuracy internal OSC (±3.0%)

QFP-36

8

256

26

2

1

12/8-bit x 11ch

✔

✔

High accuracy internal OSC (±3.0%)

QFP-36

4

128

21

—

—

12/8-bit x 8ch

✔

✔

Small scale 8bit MCU; Remote Control Receiver Circuit

SSOP-24

8-bit General

8

256

21

2

—

12/8-bit x 8ch

✔

✔

Mask ROM edition of LC87FBK08A

SSOP-24

8-bit General

16

512

26

2

1

12/8-bit x 10ch

—

—

—

QFP-36

LC87F2J32A

8-bit General

32

1024

41

2

1

12/8-bit x 14ch

✔

✔

—

SQFP-48, QIP-48

LC87F2W48A

8-bit General

50

1536

40

2

1

12/8-bit x 14ch

✔

—

—

SQFP-48

LC87F2C64A

8-bit General

64

2048

73

4

2

12/8-bit x 16ch

✔

✔

RTC; low power consumption

QFP-80

LC87FC096A

8-bit General

96

4096

55

6

2

12/8-bit x 11ch

✔

✔

12-bit PWM x 6

QIP-64E

LC87F2608A

8-bit General

8

512

7

1

—

12/8-bit x 3ch

✔

✔

High speed 12-bit PWM; Analog Comparator

MFP-10SK

LC87F0808A

8-bit General

8

256

30

6

1

10/8-bit x 10ch

✔

✔

MCPWM; High speed ADC (10-bit); Analog Comparator/Amplifier x 2

QFP-36

LC87F0N04A

8-bit General

4.5

128

12

4

—

10/8-bit x 6ch

✔

✔

MCPWM; High speed ADC (10-bit); Analog Comparator x 2

SSOP-16

LC87F0G08A

8-bit General

8

256

18

3

—

12/8-bit x 7ch

—

—

MCPWM, OP-AMP, Analog comparator

SSOP-24

LC87F0A08A

8-bit General

8

256

30

2

—

12/8-bit x 8ch

✔

✔

OP-AMP, Analog comparator, Constant current output port

QFP-36

LC87F5VP6A

8-bit General

256

10240

89

4

2

8-bit x 15ch

—

—

Large scale memory

QIP-100E

LC88F58B0A

16-bit General

128

6144

54

2

2

12/8-bit x 11ch

—

✔

Motor control signal generator

SQFP-64

LC88FC3K0A

16-bit General

768

49152

90

4

3

12/8-bit x 16ch

✔

✔

2 x SMIC, SLIIC; RTC; CRC calculation circuit

TQFP-100

LC87F7932B

8-bit LCD

32

2048

49

2

1

12/8-bit x 7ch

—

✔

32 x 4 segment driver; RTC; low power consumption

SQFP-64

LC87F7J32A

8-bit LCD

32

1024

51

2

1

12/8-bit x 12ch

✔

✔

24 x 4 segment driver; support 5 V/3 V for LCD-panel

TQFP-64

LC87F76C8A

8-bit LCD

128

4096

71

2

1

12/8-bit x 12ch

—

—

32 x 4 segment driver

QFP-80

LC87F7DC8A

8-bit LCD

128

4096

91

2

2

12/8-bit x 15ch

—

—

54 x 4 segment driver; many segment drivers

QIP-100E

LC87F7NC8A

8-bit LCD

128

4096

91

2

2

12/8-bit x 15ch

—

—

54 x 4 segment driver; large scale memory

QIP-100E

LC87F7NJ2A

8-bit LCD

192

8192

91

2

2

12/8-bit x 15ch

—

—


QIP-100E

LC87F7NP6A

8-bit LCD

256

8192

91

2

2

12/8-bit x 15ch

—

—


QIP-100E

* Mask ROM Device; Contact ON Semiconductor for additional information.

MCUs for USB MCU Features • USB 2.0 full-speed/low speed functions • USB device function/USB host function Device

Type

LC87F1A32A

8-bit USB

LC87F1M16A

8-bit USB

LC87F1K64A

8-bit USB

LC87F17C8A

8-bit USB

LC87F1HC8A LC87F1JJ2A LC87F1JJ4A LC87F1JJ8A

8-bit USB 8-bit USB 8-bit USB 8-bit USB

Page 18

ROM RAM (kByte) (Byte)

• Integrated voltage regulator • USB D+ line pull-up function

I/Os

PWMs

UARTs

ADC

LVD

POR

Features

Package

2048

39

2

1

12/8-bit x 12ch

—

—

IR reciever

SQFP-48

16

1024

38

2

1

12/8-bit x 20ch

✔

✔

UART & SCUART; high current driver

SQFP-48

64

8192

39

2

1

12-bit x 12ch

✔

✔

USB I/F x 2; USB Host; Audio I/F

SQFP-48

128

8192

39

2

1

12/8-bit x 12ch

SQFP-48

16384 16384 20480 24576

39 39 39 39

2 2 2 2

1 1 1 1

8-bit x 12ch 8-bit x 12ch 8-bit x 12ch 8-bit x 12ch

4 — — — —

USB 2.0 full speed host/device controller x2; audio IF

128 192 192 192

4 — — — —

USB Host; Audio I/F USB Host; Audio I/F USB Host; Audio I/F USB Host; Audio I/F

SQFP-48 SQFP-48 SQFP-48 SQFP-48

32


MCU Starter Kit for Software Development Trial kit includes Main Board, Sub Board, and Development Environment CD. With Main Board as a base, it is possible to connect different Sub Boards with different pin numbers. • 8 bit Easy Micon Development Tool Sub Board Line Up: 16-pin, 24-pin, 36-pin, 48-pin • 16 bit Xstromy16 Development Tool Sub Board Line Up: 48-pin, 64-pin, 100-pin

LEDs

CONTROL

Switch

Connects to PC via Standard USB Cable

MCU On-Chip Debugger System • Software development with 1 wire communication • Reduction of development time with Real Time Display function, Break function, and Trace function

Debugger (1 Wire)

Real Time Display Function Displays program running situation in real time

ON Semiconductor

Page 19

EEPROMs for Configuration and Calibration Features • Broad density range: 1 kb to 2 Mb • Wide operating Vcc range: 1.7 V to 5.5 V • High endurance: 1 million program/erase cycles • Wide temperature range: industrial and extended

EasyPRO™ is a user-friendly, portable programming tool for ON Semiconductor serial EEPROMs (I2C, SPI, Microwire)

EEPROMs Data Transmission Standard

CONTROL

I2C

SPI

Microwire

Density

Organization*

1 Mb 512 kb 256 kb 128 kb 64 kb 32 kb 16 kb 8 kb 4 kb 2 kb 2 Mb 1 Mb 512 kb 256 kb 128 kb 64 kb 32 kb 16 kb 8 kb 4 kb 2 kb 1 kb 16 kb 16 kb 8 kb 8 kb 4 kb 2 kb 1 kb 1 kb

128k x 8 64k x 8 32k x 8 16k x 8 8k x 8 4k x 8 2k x 8 1k x 8 512 x 8 256 x 8 256k x 8 128k x 8 64k x 8 32k x 8 16k x 8 8k x 8 4k x 8 2k x 8 1k x 8 512 x 8 256 x 8 128 x 8 2k x 8 / 1k x 16 2k x 8 / 1k x 16 1k x 8 / 512 x 16 1k x 8 / 512 x 16 512 x 8 / 256 x 16 256 x 8 / 128 x 16 128 x 8 / 64 x 16 128 x 8 / 64 x 16

VCC Min (V)

VCC Max (V)

fCLK Max (MHz)

Package(s)

1.7, 1.8

5.5

0.4, 1

US8, SOIC-8, TSSOP-8, UDFN-8, TSOT23-5, WLCSP-4, WLCSP-5, WLCSP-8

1.7, 1.8

5.5

10, 20

SOIC-8, TSSOP-8, UDFN-8

1.65, 1.8

5.5

2, 3, 4

SOIC-8, TSSOP-8, UDFN-8

* Organization for Microwire devices is selectable.

Page 20


Serial NOR Flash Features • Faster data rewrite (Sector Erase/Page Program) • Lower power consumption with efficient rewrite operation • 20-year data retention with no data deterioration • Consistent Sector Erase operation time (tSE) over device lifetime • Industry’s fastest WRITE performance minimizes system risk during field firmware upgrades

CONTROL

VCC

VCC VCC

CS

HOLD

SCK

CS SCK Wireless SoC

Serial Flash W P GND

SI

SI

SO

SO

LED Driver

Smart LED Block Diagram

Density

Power Supply (V)

Sector Erase Time (ms)

Page Program Time (ms)

Read/Write Current (mA)

Package

LE25S20

2 Mb

1.65 - 1.95

80

3

6 Read; 15 Write

SOIC-8, VSOIC-8

LE25U20A

2 Mb

2.3 - 3.6

80

4

6 Read; 15 Write

SOIC-8, VSOIC-8, WDFN-8

LE25U40C

4 Mb

2.3 - 3.6

80

4

6 Read; 15 Write

SOIC-8, VSON-8, VDFN-8

LE25S40

4 Mb

1.65 - 1.95

80

6

6 Read; 15 Write

SOIC-8, VSOIC-8, VDFN-8, VSON-8

LE25W81

8 Mb

2.45 - 3.6

100

0.3

6 Read; 15 Write

VSON-8, VDFN-8

LE25S81A

8 Mb

1.65 - 1.95

15

0.3

5 Read; 4.5 Erase

SOIC-8, VSOIC-8

LE25S161

16 Mb

1.65 - 1.95

15

0.4

4.5 Read; 4.5 Erase

SOIC-8, VSOIC-8, UDFN-8, WLCSP-8

Device

ON Semiconductor

Page 21

Wireless Connectivity Solutions Features • Power efficient solutions for sub-GHz and 2.4 GHz radios • Full portfolio including RF transceivers, SoC, modules, software, tools • Easy to use, robust, reliable turnkey solutions

Protocol Sigfox™ Wireless KNX®

CONTROL

802.15.4g

6LoWPAN Thread ZigBee® Proprietary

SoC Module Device

RF Device

AX-SFEU/US AX8052F143-3 AX8052F151 AX8052F143 NCS36510 AX8052F151 AX8052F143 NCS36510 NCS36510 NCS36510 AX8052F151 AX8052F143 NCS36510

— AX5243 AX5043 AX5243 AX5051 AX5043 AX5243 AX5051 — — AX5043 AX5243 AX5051

NCS36510 is a low power, fully integrated, System on Chip that integrates a 2.4 GHz IEEE 802.15.4-2006 compliant transceiver, Arm® Cortex®-M3 microprocessor, RAM and FLASH memory, a true random number generator, and multiple peripherals to support design of a complete and secure wireless network with minimal external components. • Supply voltage 1.0 – 3.6 V • Sensitivity -99 dBm; link budget 107 dBm

• Receive current: 6.7 mA @ 1 V; 3 mA @ 3 V • Transmit current: 6 mA @ 1 V

AX8052F143 is an ultra-low-power RF microcontroller that supports a wide variety of shaped modulations (FSK, MSK, 4-FSK, GFSK, GMSK, AFSK, ASK, FM). The device includes integrated FLASH, standard interfaces, analog peripherals, and GPIO. It operates on a supply voltage of 1.8 – 3.6 V, and consumes only 50 nA in Deep Sleep mode. AX5043 and AX5243 are true single chip, narrow-band, ultra-low-power ASK and FSK RF transceivers for the 27 - 1050 MHz frequency bands. They operate on a supply voltage of 1.8 – 3.6 V.

Page 22


Motor Drivers for Lens Motor Control Motor Driver for Zoom

Lens Unit

Motor Driver for Focus CPU

Motor Driver for Lens Shift (Up/Down, Left/Right)

Lens

Motor Driver for Iris

CONTROL

Key Features • Integrated active flyback protection • Thermal and UVLO fault detection • Over-current fault detection on LV8711T

Type

VM Max (V)

VCC Max (V)

IO Max (A)

Current Sense

Regulator Output

Package

LV8417CS

Brush DC

12.6

6

1

—

Parallel

None

No

WLP-9

LB1938FA

Brush DC

10.5

—

0.8

—

Parallel

None

No

Micro8

LV8548MC

Stepper/Brush DC

20

—

1

1/2

Parallel

None

No

SOIC-10

LV8711T

Stepper/Brush DC

18

6

0.8

1/2

Parallel

External Resistor

Yes

TSSOP-24

LV8714TA

Stepper/Brush DC

18

—

1.5

Free

Parallel

External Resistor

No

TQFP-48EP

LV8402GP

Stepper/Brush DC

16

6

1.4

1/2

Parallel

None

No

VCT-24

LV8716QA

Stepper/Brush DC

12.6

—

1

1/2

Parallel

External Resistor

No

QFN-16

LV8413GP

Stepper/Brush DC

6

6

0.4

1/2

Parallel

None

No

VCT-16

LV8414CS

Stepper/Brush DC

6

6

0.4

1/64

Clock

External Resistor

No

WLP-32K

LV8549MC

Stepper

20

—

1

Full Step

Parallel

None

No

SOIC-10

LV8712T

Stepper

18

6

0.8

1/8

Clock

External Resistor

Yes

TSSOP-24

LV8713T

Stepper

18

6

0.8

1/32

Clock

External Resistor

Yes

TSSOP-24

Device

ON Semiconductor

Step Control Type Resolution

Page 23

Cascadable I/O Expanders Features • I2C and SMBus interfaces • 1 MHz SCL clock frequency • 30 mA SDA sink capability

3.3 V 12 V

Button LED SCL SDA

SCL SDA

I/O I/O

INT

I/O I/O

μC GPIO Vext

I/O I/O

I/O I/O

Hot-Plug Controller

AUXEN PWRFLT

12 V MOSFETs 3.3 V

Hot-Plug Controller

AUXEN PWRFLT

12 V

CONTROL

PRSNT2 PRSNT2

I/O I/O

I/O

Slot 2 Slot 3 3.3 V

PCA96xxE PCA95xxE I/O Expander

LEDs

Backplane Systems

I/O I/O I/O I/O

Keypad Control

ADM1033 Thermal Sensor and Fan Controller

Temperature Control

Device

I/O

Cascadable

VCC Min (V)

VCC Max (V)

Interrupt Output

PCA9535E

16

64 Programmable Slave Addresses

1.65

5.5

4

QFN-24, SOIC-24, TSSOP-24

PCA9655E

16

64 Programmable Slave Addresses

1.65

5.5

4

QFN-24, SOIC-24, TSSOP-24

PCA9654E

8

8 Slave ID Addresses

1.65

5.5

4

4

SOIC-16, WQFN-16, TSSOP-16

FXL6408

8

—

1.65

3.6/4.0

4

4

UMLP-10

Page 24

I/O Pullups

Package


Digital Potentiometers (POTs) for Trimming and Calibration RH0

Features

SCL SDA

• No drift over time or temperature • No changes due to mechanical stress or shock • Systems can be calibrated real-time, in the field • Broad portfolio provides for selection of optimal number of pots and taps

PC BUS INTERFACE

ON Semiconductor

Number of Taps 16 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 100 100 100 128 128 128 128 256 256 256 64 64 64 256 256 256 256 64 64 64 256 256

Resistance (kΩ) 10, 50, 100 10, 50, 100 10, 50, 100 10, 50, 100 10, 50, 100 10, 50, 100 10, 50, 100 10, 50, 100 10, 50, 100 10, 50, 100 10, 50, 100 10, 50, 100

10, 50, 100 1, 10, 50, 100 32 (Log Taper) 10, 50, 100 10, 50, 100 50 10 50, 100 50, 100 50 2.5, 10, 50, 100 2.5, 10, 50, 100 2.5, 10, 50, 100 50, 100 50, 100 50, 100 50 2.5, 10, 50, 100 2.5, 10, 50, 100 2.5, 10, 50, 100 50, 100 50, 100

RH3

RW0 RW1

WP A0 A1 A2 A3

RW2 NONVOLATILE DATA REGISTERS

CONTROL LOGIC

RW3

Buffered Wiper

3

3

Interface UP/DOWN UP/DOWN UP/DOWN UP/DOWN UP/DOWN UP/DOWN UP/DOWN UP/DOWN UP/DOWN UP/DOWN UP/DOWN UP/DOWN UP/DOWN UP/DOWN UP/DOWN UP/DOWN UP/DOWN UP/DOWN UP/DOWN I²C UP/DOWN I2C I2C I2C I2C SPI I²C SPI I²C SPI I²C I2C I2C I²C SPI I²C SPI I²C

NonVolatile

Volatile 3 3

3 3 3 3 3 3 OTP 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3

RL1

RL2

RL3

Packages SOT-23–6, SC-70–6 SOT-23–6, SC-70–6 PDIP–8, SOIC–8, MSOP–8, TSSOP–8 PDIP–8, SOIC–8, MSOP–8, TDFN-8, TSSOP–8 PDIP–8, SOIC–8, MSOP–8, TSSOP–8 SOT-23–5, SC-70–5 SOT-23–5 SOT-23–6 MSOP-8, TDFN-8 MSOP-8, TDFN-8 SOT-23–8 TSOT-23–6 SOIC–8, MSOP–8, TDFN-8, TSSOP–8 SOIC–8, MSOP–8, TDFN-8, TSSOP–8 SOIC–8, MSOP–8, TDFN-8, TSSOP–8 SOT-23-8 PDIP–8, SOIC–8, MSOP–8, TSSOP–8 PDIP–8, SOIC–8, MSOP–8, TSSOP–8 PDIP–8, SOIC–8, MSOP–8, TSSOP–8 MSOP–10 MSOP–10 SC-88-6, SC-70-6 SC-88-6, SC-70-6 MSOP-8 SOT-23-8 SOT-23-8 SOIC–20, TSSOP–20 SOIC–24, TSSOP–24 SOIC–24, TSSOP–24 SOIC–24, TSSOP–24 SOIC–24, TSSOP–24 MSOP-10 MSOP-10 SOIC–20, TSSOP–20 SOIC–24, TSSOP–24 SOIC–24, TSSOP–24 SOIC–24, TSSOP–24 SOIC–24, TSSOP–24 Page 25

CONTROL

Number of Pots 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 4 4 4 4 4

RH2

WIPER CONTROL REGISTERS

RL0

Device CAT5120/1/2 CAT5110 CAT5112 CAT5114 CAT5115 CAT5118/9 CAT5123/4 CAT5125 CAT5126 CAT5127 CAT5128 CAT5129 N57M5114 N57L5125 N57M5127 N57L5128 CAT5111 CAT5113 CAT5116 CAT5132 CAT5133 CAT5137 CAT5138 CAT5140 CAT5171 CAT5172 CAT5221 CAT5411 CAT5419 CAT5261 CAT5269 CAT5271 CAT5273 CAT5241 CAT5401 CAT5409 CAT5251 CAT5259

RH1

Active Cable USB-C active cables have the ability to interface to multiple devices with one single cable and eliminate the need for individual cables for each end device. Meanwhile, mitigating signal integrity losses have become a design challenge for the higher data rate possible with USB 3.1 Gen 1 and Gen 2. USB active cable solutions from ON Semiconductor enable highprecision, low jitter, high gain equalization with full USB compliance and interoperability. We also provide high speed line data ESD protection products.

System Devices

Data Path

Control

Protection

Data Redriver

Port Control

Block Diagram

System Devices Function

USB-C

Protection

Device

Description

ESDL2011

High Speed Data Line Protection, Bidirectional (1 V – Thunderbolt 3.0), 0.2 pF

ESD8111

High Speed Data Line Protection (3.3 V – USB 3.x), (Tx/Rx Pairs), 0.4 pF

ESDM3551

ESD Protection Diode, CC and SBU Protection (5.5 V – USB 3.x), 21 pF

NSPM2052

ESD and Surge Protection Device, Vbat and Vbus Applications, 5 V

NSPM5131

ESD and Surge Protection Device, Unidirectional, 13.5 V

FUSB252UMX

High Speed Digital (HSD) Port Protection Switch with Type-C CC

Data Path Function

Data Redriver

Device

Description

NB7NPQ7021M

USB 3.1 Dual Channel Linear Redriver, 3.3 V

NB7NPQ702M

USB 3.1 Dual Channel Redriver, 3.3 V

NB7VPQ702M


NB7NPQ701M

USB 3.1 Single Channel Redriver, 3.3 V

NB7VPQ701M


Control Function

Device

Port Control FUSB302BUCX

Page 26

Description Programmable USB Type-C Controller with PD (Default SNK)


Docking Station Greater adaptation of USB-C has caused manufactures to introduce many USB Type-C devices, including for mobile PCs, tablets, and docking stations. There are various USB-C universal docking stations to connect multiple laptop platforms and peripherals. ON Semiconductor provides docking station solutions including the USB Type-C Data Hub (USB protocol & signal conditioning), as well as the charging capability for the USB Type-C systems that support USB Power Delivery/Alternate mode protocol.

System Devices

Port Power

Data Path

Control

Voltage Regulation

Power Regulation

Data Redrvicer

Controllers

Protection

Power MUX

SuperSpeed MUX

Port Control

Sensors

Power Switch

Alt Mode MUX

Policy Engine

Block Diagram

Function Voltage Regulation

Protection

Device

Description

NCP81239

4-Switch Buck Boost Controller, USB Power Delivery and Type C Applications

NCP81231

Buck Controller, USB Power Delivery and Type-C Applications

FUSB252UMX

High Speed Digital (HSD) Port Protection Switch with Type-C CC

ESD8704

High Speed Data Line Protection, Unidirectional (3.3 V – USB 3.x)

ESDL2011

High Speed Data Line Protection, Bidirectional (1 V – Thunderbolt 3.0), 0.2 pF

ESDM3551

ESD Protection Diode, CC and SBU Protection (5.5 V – USB 3.x), 21 pF

NSPM2052


NIS5452

Electronic Fuse, 5 V

Power Port Function

Power Regulation

Power MUX

Data Path Function

Data Redriver

SuperSpeed Mux

Device

Description

NB7NPQ7021M

USB 3.1 Dual Channel Linear Redriver, 3.3 V

NB7NPQ701M


NB7NPQ702M


NB7VPQ701M


NB7VPQ702M


FUSB340TMX

USB 3.1 SuperSpeed Switch, 10 Gbps

Control Device

Description

NCP1342

Quasi-Resonant Flyback Controller with Valley Lock-Out Switching

NCP4305

Secondary Side Synchronous Rectification Driver for High Efficiency SMPS Topologies

NCP4306


NCP43080

Synchronous Rectifier Controller with LLD Function

FPF2595UCX

Load Switch, Over-Voltage, Over-Current Protection with Adjustable Current-Limit Control, IntelliMAX™ 28 V

FPF2895CUCX

Current Limit Load Switch with OVP and TRCB, 28 V, 5 A

ON Semiconductor

Function

Port Control

Device

Description

FUSB302TMPX

Programmable USB Type-C Controller with PD (Default SRC)

FUSB303TMX

Autonomous USB Type-C Controller with I2C and GPIO Control

FUSB307BMPX

USB Type-C Port Controller with USB-PD

Page 27

USB-C

System Devices

USB Wall Receptacle Wall receptacles that include direct USB cable connections are becoming increasing popular for charging mobile devices. ON Semiconductor offers high performance, high density USB-C power supplies for the USB wall receptacle solutions.

System Devices

Port Power

Control

Voltage Regulation

Power Regulation

Controllers

Protection

Power MUX

Port Control

Sensors

Power Switch

Policy Engine

Block Diagram

System Devices Function

USB-C

Protection

Device

Description

NIS5452


ESD5581

ESD Protection, Bidirectional, 5 V, 10 pF

NSPM2052


NSPM0061

ESD and Surge Protection, 6.3 V

NSPM0101

ESD and Surge Protection, 10 V, 60 A

NSPM5131


Power Port Function Power Regulation

Device

Description

NCP1342


NCP4305


NCP4306


NCP43080


Control Function Port Control

Page 28

Device

Description

FUSB302TMPX


FUSB3301MPX

USB Type-C Source-Only Controller


AC-DC Wall Adapter ON Semiconductor provides AC-DC wall adapter solutions compatible with the latest USB-C (Type-C) and Power Delivery (PD) specifications. Our solutions are integrated, compact, highly efficient solutions that consume minimal quiescent current to minimize heat dissipation. Fast charge solutions are available, and are compatible with Nebo or existing microcontroller.

System Devices

Port Power

Control

Voltage Regulation

Power Regulation

Controllers

Protection

Power MUX

Port Control

Sensors

Power Switch

Policy Engine

Block Diagram

System Devices Device

Voltage Regulation

FAN6291QH

Secondary-Side Adaptive Charging Controller, Synchronous Rectifier and USB Type-C Control

NIS5452


ESD5581

ESD Protection, Bidirectional, 5 V, 10 pF

NSPM2052


NSPM0101

ESD and Surge Protection, 10 V, 60 A

NSPM5131


NSPM0061

ESD and Surge Protection, 6.3 V

NCS210

Current Sense Amplifier, Bidirectional Zero-Drift, 1% Max. Gain Error, 60 µV Offset

NCS211


NCS213


Function

NCS214


Port Control

NCS2333

Precision Operational Amplifier, Low Power, Zero-Drift, 30 µV Offset

Protection

Description

USB-C

Function

Control Device

Description

FUSB302TMPX


FUSB3301MPX

USB Type-C Source-Only Controller

Power Port Function

Power Regulation

Power MUX

Device

Description

NCP1342


NCP4305


NCP4306


NCP43080


FPF2595UCX

Load Switch, Over-Voltage, Over-Current Protection with Adjustable Current-Limit Control, IntelliMAX™ 28 V

FPF2895CUCX

Current Limit Load Switch with OVP and TRCB, 28 V, 5 A

ON Semiconductor

Page 29

Power Bank USB-C (Type-C) is becoming the latest standard for accessories including power banks. ON Semiconductor offers both discrete and best-in-class integrated power bank solutions, which meet the latest USB-C and USB Power Delivery (PD) specifications. Our latest integrated, scalable power bank solutions enable a streamlined design process, and accelerate time to market, supporting a range of battery pack sizes. System Devices Function

Device NCP1340

Voltage Regulation

Protection

Port Control

NCP1341 NCP43080 NCP4306 NCP4371 ESD8704 ESD7104 ESD8116 ESD8118 LC06111TMT LC05711ARA LC05111CMT FUSB252UMX FUSB302TMPX FUSB303TMX FUSB307BMPX

Description Quasi-Resonant Controller, High-Voltage, Featuring Valley Lock-Out Switching Quasi-Resonant Controller, High-Voltage, Featuring Valley Lock-Out Switching with Power Excursion Mode (PEM) Synchronous Rectifier Controller with LLD Function Secondary Side Synch Rec Driver for High Efficiency SMPS Topologies HVDCP Controller for Qualcomm Quick Charge 3.0 High Speed Data Line Protection, Unidirectional (3.3 V – USB 3.x) ESD Protection, Low Capacitance, High Speed Data ESD Protection Array, USB 3.0 ESD Protection Array, USB 3.0 Battery Protection IC, Integrated Power MOSFET, 1-Cell Lithium-Ion Battery Battery Protection IC, Integrated Power MOSFET, 1-Cell Lithium-Ion Battery Protection Controller with Integrated MOSFET, 1-Cell Lithium-Ion High Speed Digital (HSD) Port Protection Switch with Type-C CC Programmable USB Type-C Controller with PD (Default SRC) Autonomous USB Type-C Port Controller with I2C and GPIO Control USB Type-C Port Controller with USB-PD

USB-C

Port Power Function Power Regulation

Power MUX

Page 30

Port Power

Control

Voltage Regulation

Power Regulation

Controllers

Protection

Power MUX

Port Control

Sensors

Power Switch

Policy Engine

Block Diagram

Control Device

Description

NCP81231 NCP81239

Buck Controller, USB Power Delivery and Type-C Applications 4-Switch Buck Boost Controller, USB Power Delivery and Type C Application

FPF2280

Over-Voltage Protection Load Switch

FPF2281


FPF2290


FPF2495 Power Switch

System Devices

FPF2595 ECH8310 NTTFS4H05N MCH3375 BAT54AL BAT54CL BAT54T FPF2595UCX FPF2895CUCX

Load Switch, Over-Voltage, Over-Current Protection with Adjustable Current-Limit Control, IntelliMAX™ 28 V Load Switch, Over-Voltage, Over-Current Protection with Adjustable Current-Limit Control, IntelliMAX 28 V P-Channel Power MOSFET, -30 V, -9 A, 17 mΩ Power MOSFET, Single N−Channel, 25 V, 94 A, 3.3 mΩ Single P-Channel Power MOSFET, -30 V, 295 mΩ, -1.6 A Schottky Diode, Dual Common Anode, 30 V Schottky Diode, Dual Common Cathode, 30 V Schottky Barrier Diode Load Switch, Over-Voltage, Over-Current Protection with Adjustable Current-Limit Control, IntelliMAX 28 V Current Limit Switch with OVP and TRCB, 28 V / 5 A

Function Controllers/ Policy Engine

Device LC709501F

LC709511F FUSB302 FUSB302B

Port Control

FUSB302TMPX FUSB303TMX FUSB307BMPX

Description Power Bank Controller, USB Type-C & Quick Charge™ 3.0, for 1-Cell Li-Ion and Li-Poly Battery Power Bank Controller, USB Type-C & Quick Charge 3.0, for 1-Cell Li-Ion and Li-Poly Battery Programmable USB Type-C Controller with PD Programmable USB Type-C Controller with PD (Default SNK) Programmable USB Type-C Controller with PD (Default SRC) Autonomous USB Type-C Port Controller with I2C and GPIO Control USB Type-C Port Controller with USB-PD


Clock Generation and Distribution Numerous Clock Interfaces

Antenna Satellite CATV

AC In

Input Amp

• Programmable PLL Clocks can satisfy all clock tree requirements with pin-strap, OTP, I2C • Maintain clock architecture flexibility with ability to program new clock configurations through software • Fixed frequency for specific applications • PLL-based Zero Delay Buffers • EMI reduction using spread spectrum frequency modulation to reduce peak emissions • Low jitter guarantees synchronous system

L Audio In

Input Amp Smart Card Interface

R L

I/O Interface Audio Amp

Audio Out Audio Switch

Codec/ Modem Audio Codec

MCU

ADC

Audio Filter

Audio Amp

Clock Generation

R

LCD Backlighting

Display

Video Processor

DAC

Video Filter

Video Amp

S-Video Out

DAC

Video Filter

Video Amp

Composite Video Out

Tuner

Video Switch

Video Filter

Input Bridge Rectification

Power Factor Correction

Voltage Regulation (Switching)

SMPS

Transformer

Output Rectification/ Sync Rect

Optoisolation

Reference/ Error Amplifier

Voltage Regulation (Linear, Switching)

Clock Distribution

Supervisory

Set Top Box

Clock Generators

• Low power with integrated LDO extends battery life • Low additive noise for reliable system operation • Low output skew assures proper signal timing • Flexible interface options, i.e., voltage translation, input/output compatibility

Clock Fanout Buffers Output Frequency (MHz)

Application

Package

FS6370/7

150

Video

SOIC-16

FS7140/5

150 CMOS, 340 PECL

Printers, Video

SOIC-16, SSOP-16

NB3N551

3.3, 5.0

180

NB3N3002

25, 100, 125, 200

PCI-e, Gigabit Ethernet

TSSOP-16

NB3L553

NB3N3010B

12.288

USB

SOIC-8, DFN-8

2.5, 3.3, 5.0

NB3N2304NZ

NB3N3020

210

Network Video

TSSOP-16

NB3N501

13-160

CPU, USB, PCI, Network

SOIC-8

NB3N502

14-190

CPU, USB, PCI, Network, Ethernet

SOIC-8

100, 200

PCI-e, DIMM, CPU

TSSOP-20

NB3N511

14-200 with selectable multiplier ratios

USB, PCI, PCI-e, SDRAM, Ethernet, Gigabit Ethernet, CPU

SOIC-8

NB3N5573

25, 100, 125, 200

PCI-e, DIMM, CPU

TSSOP-16

NB3x63143G

0.008-200

Printers, Video

QFN-16

NB3x60113G

0.008-200

Printers, Video

DFN-8

Device

NB3N51032/4

Device

Output Freq Outputs (MHz)

Type

Package

4

Fanout Buffer

SOIC-8, DFN-8

200

4

Fanout Buffer

SOIC-8, DFN-8

3.3

140

4

Low Skew Fanout Buffer

TSSOP-8, DFN-8

P2I2305NZ

3.3

133

5

Clock Fanout Buffer

SOIC-8

PCS2P2309NZ

3.3

133

9

Clock Fanout Buffer

SOIC-16

NB2304A/5A

3.3

15-133

4, 5

Zero Delay Buffer

TSSOP-8, SOIC-8

NB2309A

3.3

15-133

8, 9

Zero Delay Buffer

TSSOP-16, SOIC-16

NB2304A

3.3

15-133

4

Zero Delay Buffer

SOIC-8

1.8, 2.5, 3.3

250

2, 3, 4, 6, 8


TSSOP-8, WDFN-8, TSSOP-14, TSSOP-16

3.3

200

2, 4


SOIC-8

1.8, 2.5, 3.3

100

6

NB3V110xC

NB3M8302C/4C NB3H83905C

ON Semiconductor

VCC (V)

SOIC-16, Clock Fanout Buffer TSSOP-16, QFN-20

Page 31

TIMING

VOIP DSL Analog Phone Line

Line Protection

Smart Card

I/O Protection

Keypad IEEE1394 ATA PI USB Ethernet PCI Flash Memory Infrared

Clock Generation

OmniClock Programmable Clock Synthesizers Fits Many Systems, Extends Battery Life, Reduces EMI, and Saves Board Space Key Features • Single PLL • Input Frequency Range: • Crystal: 3 – 50 MHz (low cost ESR crystal compatible) • Clock: 3 – 200 MHz (single-ended only) • Up to 3 single-ended (LVCMOS/LVTTL) outputs, or up to 1 differential (LVPECL, LVDS, HCSL or CML) output + 1 single-ended (LVCMOS/LVTTL) output • Output Frequency Range: 8 kHz (Min), 200 MHz (Max) • Programmable Spread Spectrum Capabilities for EMI Suppression • Center Spread (0.125% steps): ± 0.125% to ± 3% • Down Spread (0.25% steps): -0.25% to -4% • Modulation Rate: 30 kHz – 130 kHz • PLL Bypass mode • Individual Output Enable pin for each output and Power Down Capability • Individual Output Voltage pins per output, allowing setting of output voltage (1.8 V, 2.5 V or 3.3 V; equal to or less than VDD) • Automatic Gain Control (Crystal Power Limiting) • Programmable internal input crystal load capacitors • Programmable Output Drive current • Up to 4 independent configurations using SELx pins • Supply Voltage: 3.3 V ±10%; 2.5 V ± 10%; 1.8 V ± 0.1 V

VDD

PD#

SEL0

SEL1

Input Decoder Crystal/Clock Control

Configuration Memory

Output Control VDDO0

Frequency and SS Reference Clock

XIN/CLKIN

TIMING

Clock Buffer/ Crystal Oscillator and AGC

Crystal XOUT

PLL Block Phase Detector

Charge Pump

Output Divider VCO

CMOS/ DIFF Buffer

CLK0 OE0 VDDO1

Feedback Divider

Output Divider

CMOS/ DIFF Buffer

CLK1 OE1 VDDO2

Output Divider

CMOS Buffer

CLK2

PLL Bypass Mode OE2 GND

GNDO

Block Diagram Page 32


Implementation of OmniClock Programmable Clock Synthesizers Using OmniClock in Your System

Customer orders blank OmniClock devices

Customer uses free GUI and supplied evaluation board to configure the blank device to the desired parameters: frequency, drive strength, spread spectrum, etc.

Customer provides configuration file to ON Semiconductor sales channel

ON Semiconductor programs device in factory with desired customer configuration, and creates customer-specific part number

Individual OE

Individual Vddo

Supply Voltage (V)

Number of Configurations

Number of Outputs

Package

NB3H63143G

Yes

Yes

2.5 / 3.3

4

3

QFN-16

NB3H60113G

No

No

2.5 / 3.3

1

3

DFN-8

NB3V63143G

Yes

Yes

1.8

4

3

QFN-16

NB3V60113G

No

No

1.8

1

3

DFN-8

Device

ON Semiconductor

TIMING

Configuration GUI

Page 33

Low Noise Clock Buffers NB3RL02 has two CMOS outputs with clock request lines. Systems in need of TCXO clock will request clock from NB3RL02, and NB3RL02 powers the TCXO and delivers the requested clock, eliminating multiple TCXOs.

NB3RL02 Key Features

NB3RL02

• Frequency: 10-52 MHz • Low additive noise: −149 dBc/Hz at 10 kHz offset phase noise • 0.37 ps (rms) output jitter • Limited output slew rate for EMI reduction (1 to 5 ns rise/fall time for 10−50 pF loads) • Integrated, regulated 1.8 V externally available I/O supply • ESD performance exceeds JESD 22 • WLCSP-8 package

VLDO 2.2 μF

LDO

VBATT 1 μF

Li

CLK_REQ_1

TCXO REQ

CLK_OUT_1 MCLK_IN

TCXO CLK

CLK_REQ_2

TCXO REQ

CLK_OUT_2

TCXO

DTV

TCXO CLK

GND

WLAN

NB3RL02 Used to Clock Multiple Applications and Power a TCXO

NB3L02 VBATT

GPS

LDO

NB3L02/03 Key Features CLK_OUT1

MCLK_IN

CLK_OUT2

• 1:2, 1:3 Fanout • Low phase noise TCXO buffer • AC coupled input accepts sin wave or square wave • WLCSP-6 package

TCXO CLK

TCXO CLK

TCXO WLAN GND

NB3L02 Clocking Two Applications UFS Host

UFS Device

Application

TIMING

1.2 V

NB3U23C Key Features

0 - 1.8 V Driver

UFS Host Controller

RESET_n REF CLK

NB3U23C

0 - 1.2 V 0 - 1.2 V

UIC DOUT_t MIPI UniProSM

UFS Host Reg

MIPI M-PHYSM

• Low phase noise • Low standby current • Dual channel voltage translator/buffer • Targeted for Universal Flash Storage (UFS) applications • SC-70-6, UDFN-6 packages

0 - 1.8 V

DOUT_c DIN_t DIN_c

NB3U23C Used for Voltage Translation Page 34


Active EMI Solution for MIPI Interface in Ethernet Applications Data Clock

SDRAM

ASIC Controller + MAC

Multiple Phone Lines Data Clock

Use conventional spread spectrum device at the crystal source, to reduce EMI globally

PHY

Ethernet Port(s)

Use Timing Safe™ spread spectrum devices on clocks synchronized with data, to reduce EMI locally

Timing Safe Technology maintains data synchronization on clock line

Spread Spectrum Enabled

Spread Spectrum Disabled

Device ASM3P2111B ASM3P2182A ASM3P2760A ASM3P2775A ASM3P2812A ASM3P2863A P1P8160A P2042A P3I2005A P3MS650103H P3P8220A P3PS850BH PCS3P25811A PCS3P7303A PCS3P8504A PCS3PS550A ON Semiconductor

fout Typ (MHz) 48, 66 25-210 6-12, 6-13 13-30 20-80 6-12, 6-13 27, 100 30-110 10-30, 30-100 15-30, 15-60 0-60 18-72 4-32 10-70, 10-80 15-50 18-36

VCC Typ (V) 3.3 3.3 2.5, 3.3 3.3 3.3 2.5, 3.3 3.3 3.3 3.3, 5 1.8, 2.5, 3.3 1.8, 2.5, 3.3 2.3-3.6 3.3 2.5, 3.3 3.3 2.3-3.6

Package SOIC-8 SOIC-8 TSOP-6 TSOP-6 SOIC-8 TSOP-6 WDFN-10 TSSOP-8 SOIC-8 WDFN-4 WDFN-8 WDFN-8 SOIC-8 WDFN-8 WDFN-8 WDFN-8

TIMING

Spread Spectrum EMI Reduction Clocks

EMI Clocks Key Features • Modulates the output of a PLL in order to ‘spread’ the bandwidth of a synthesized clock • Decreases the peak amplitudes of the clock’s harmonics • Reduces BOM for PCB, including ferrite beads, special casing & shielding, passive components for filtering, etc.

Page 35

TV LED Control Panel Vin 12 V

N-channel MOSFET x 2 + SBD DC/DC Converter

VCC3 + 1.8 V FRC

LED

Synchronous Rectification VCC4 + 1.0 V N-channel MOSFET x 2 + SBD T-Con

LCD Power Suppy

Back Charge Pump Charge Pump

SBD

VCC2 + 1.2~1.8 V

SBD(2in1) SBD(2in1)

VGL - 7 V Gate Driver

VGH + 35 V NPN Transistor

SBD Boost

VS + 15.7 V

Level Shifter

G Slope +34.3 V

Gamma Ref Voltage

Level Shifter

P-channel MOSFET

N-channel MOSFET

+15.2 V

HV-LDO

Gamma Buffer Amp

Memory Back

VCC 1.3 V

EEPROM 128K~512K

VCOM Amp

NPN/PNP Transistor

NOR Flash 2M~32M

VCOM + 6.5 V

= Discrete Devices

➀ N-Channel MOSFETs for Boost Chopper VDSS (V)

VGSS (V)

ID (A)

RDS(on) @ 10 V Typ/Max (W)

Qg Typ (nC)

Package

MCH6445-TL-W

60

±20

4

60/78

10

SC-88FL/MCPH-6

CPH6442-TL-W

60

±20

6

33/43

20

CPH-6

2SK3703-1E

60

±20

30

20/26

40

TO-220F-3FG

2SK3816-DL-1E

60

±20

40

20/16

40

D2PAK

Device

➁ SBD for 2-in-1 Charge Pump VF VRRM (V)

IO (A)

IF (A)

Max (V)

VR (A)

Max (mA)

Package

SBE805-TL-W

30

0.5

0.5

0.55

15

30

CPH- 5

SBE807-TL-W

30

1

0.7

0.5

16

15

CPH- 5

SB80W06T-TL-H

30

8

3

0.6

30

100

DPAK/TP-FA

Device

Page 36

IR


TV LED Control Panel

VDSS (V)

VGSS (V)

ID (A)

MCH6341-TL-W

-30

±20

-5

MCH6342-TL-W

-30

±10

-4.5

CPH6341-TL-W

-30

±20

-5

CPH6350-TL-W

-30

±20

-6

ECH8315-TL-W

-30

±20

ECH8667-TL-H

-30

±20

Device

RDS(on) @ 10 V RDS(on) @ 4.5 V Typ/Max Typ/Max (W) (W)

Qg Typ (nC)

Package

71/100

10

MCPH-6/SC-88FL

—

56/73

8.6

MCPH-6/SC-88FL

45/59

71/100

10

CPH-6

33/43

58/82

13

CPH-6

-7

19/25

31/44

18

ECH-8(S)/SOT-28FL

-5.5

30/39

55/77

13

ECH-8(D)/SOT-28FL

45/59

(Circuit) IN 12 V ➞ OUT 6.5 V

LED

➂ P-Channel MOSFETs for Boost Chopper

(Gate Slope Circuit)

VCC = 12 V NPN

PNP

5.5 V

6.5 V

(NPN Side) IC ICP = 1~3 A (Subject to inch)

➃ Bipolar Transistors for V-com Power Supply Circuit VCE(sat) Polarity

VCEO (V)

IC (A)

hFE

IC (A)

IB (A)

Typ/Max (V)

Package

MCH6102-TL-E

PNP

-30

-1.5

200-560

-0.75

-0.015

-0.25/-0.375

MCPH-6/SC-88FL

MCH6202-TL-E

NPN

30

1.5

200-560

0.75

0.015

0.15/0.225

MCPH-6/SC-88FL

PCP1103-TD-H

PNP

-30

-1.5

200-560

-0.75

-0.015

-0.25/-0.375

PCP-1/SOT-89

PCP1203-TD-H

NPN

30

1.5

200-560

0.75

0.015

0.15/0.225

PCP-1/SOT-89

2SA2124-TD-E

PNP

-30

-2

200-560

-1.5

-0.075

-0.2/-0.4

PCP-1/SOT-89

2SA2126-TL-H

PNP

-50

-3

200-560

-1

-0.05

-0.135/-0.27

DPAK/TP-FA

2SA2039-TL-E

PNP

-50

-5

200-560

-2

-0.1

-0.255/-0.43

DPAK/TP-FA

2SC5706-TL-H

NPN

50

5

200-560

2

0.1

0.16/0.24

DPAK/TP-FA

CPH3140-TL-E

PNP

-100

-1

140-400

-0.4

-0.04

-0.2/-0.6

CPH-3

CPH3240-TL-E

NPN

100

1

140-400

0.4

0.04

0.1/0.4

CPH-3

2SA1416T-TD-E

PNP

-100

-1

200-400

-0.4

-0.04

-0.2/-0.6

PCP-1/SOT-89

2SC3646T-TD-E

NPN

100

1

200-400

0.4

0.04

0.1/0.4

PCP-1/SOT-89

Device

ON Semiconductor

Page 37

250 V N-Channel MOSFETs for LED TV Features

LED

• Ultra Low On-Resistance • Improves efficiency by reducing conduction loss • Low Gate Charge • Ease of drive, faster turn-on • High Speed Switching • Reduces dynamic power loss • 100% Avalanche Tested • Voltage overstress safeguard

DPAK IPAK

Control IC

Power Board of LED-Backligh (TVs, PCs)

Device

VDSS (V)

NDDP010N25AZT4H NDDP010N25AZ-1H SFT1452-TL-W SFT1452-W

250

ID (A)

RDS(on) @ 10 V Typ/Max (W)

Qg Typ (nC)

10

0.32/0.42

16

3

PCP1402-TD-H

1.2

PCP1405-TD-H

0.6

Package DPAK/TP-FA IPAK/TP DPAK/TP-FA

1.8/2.4

4.2

IPAK/TP PCP-2/SOT-89

5/6.5*

2.1

PCP-2/SOT-89

* VGS = 4.5 V

Page 38


Boost for Satellite LNB Boost Converters for Satellite LNB fSW (kHz)

Vin Min (V)

Vin Max (V)

Vout (V)

Comments

Package

LV56351HA

425

8

23

set by resistor

Boost plus LDO for satellite LNB; programmable output; short circuit protection

HSSOP-14

LV5636VH

1000

8

23

15.9/11.7

Boost plus LDO for satellite LNB; fixed output; short circuit protection

HSSOP-14

TUNING

Device

Phone Jack Ethernet HDMI

AC Input

Video Out

USB

Satellite Antenna

POWER BOARD

AUDIO SIGNAL BOARD DC-DC

5.8 V

LDO

Filter Boost for LNB

AC-DC

12 V

16 V

5V

Tuner

DC-DC 1.2 V

DC-DC

5V

1.8 V

DC-DC

Additional Circuits

2.5 V Memory

Core LSI

FRONT DISPLAY BOARD

ON Semiconductor

Page 39

Discrete Devices for Satellite TV Tuners IOUT RF Input

LNA

RF Output

LNA

Recovery IC

QOUT PLL AGC

IF Output

Crystal

TUNING RF Devices for Satellite TV Tuners Block

Device

LNA (MMIC)

SMA3103 SMA3109

Block

Device

LNA

Page 40

MCH4020 MCH4009

VCC (V)

ICC (mA)

Gp @ 1GHz (dB)

NF @ 1GHz (dB)

P1dB @ 1GHz (dBm)

Package(s)

5 3

19 16

26.5 23

4.7 4.3

8.2 6.4

MCPH-6/SC-88FL MCPH-6/SC-88FL

VCBO (V)

VCEO (V)

IC (mA)

fT (GHz)

Package(s)

15 10

8 3.5

150 40

16.0 @ VCE = 5 V/IC = 50 mA 25.0 @ VCE = 3 V/IC = 20 mA

MCPH-4/SC-82AB MCPH-4/SC-82AB


Si-MMIC Series for Satellite TV, LNB, STB SMA3103 Features

SMA3109 Features

• High Gain: Gp=26.5dB •Wide Band: f = 950-2150 MHz •Low Current: ICC = 19 mA •High Power: P1dB = 8.2 dBm •Package: MCPH-6/SC-88FL

• Low Voltage: • Low Current: • High Gain: • Wide Band: • High Power: • Package:

VCC = 3 V ICC = 16 mA Gp = 23 dB fu = 3.6 GHz P1dB = 6.4 dBm MCPH-6/SC-88FL

TUNING

Technology Performance

30

SMA3109

25 20

Market 15 Wide Band High Gain

10

MCPH-6/SC-88FL 2.0 x 2.1 x 0.9 mm

5 0

MIX

0

1000

2000

3000

4000

SMA3109, SMA3101 SMA3103 SBX201C SMA3103 1st IF MCH4009

2nd IF

IF-Amp MMIC

Tuner/AGC/... LSI

DR Osc

IF Amplifier for Satellite TV, LNB, STB

ON Semiconductor

Page 41

Discrete Devices for Terrestrial TV/CATV Tuners Tuner IC Low Band

RF Input

IF AMP

LNA Mid Band

RF Output

High Band

LNA

IF Output AGC

PLL

TUNING RF Devices for Terrestrial TV/CATV Tuners Block

LNA

Page 42

Device MCH4014 MCH4015 MCH4020 CPH6001A 2SC5226A

VCBO (V)

VCEO (V)

IC (mA)

fT (GHz)

Package(s)

20 20 15 20 20

12 12 8 12 10

30 100 150 100 70

10.0 @ VCE = 5 V/IC = 10 mA 10.0 @ VCE = 5 V/IC = 50 mA 16.0 @ VCE = 5 V/IC = 50 mA 6.7 @ VCE = 5 V/IC = 30 mA 7.0 @ VCE = 5 V/IC = 20 mA

MCPH-4/SC-82AB MCPH-4/SC-82AB MCPH-4/SC-82AB CPH-6 MCP/SC-70FL


MCH4000 Series for Terrestrial TV/CATV Tuners MCH4014, MCH4015 Features • High Voltage: VCEO = 12 V • High Gain: MCH4014: |S21e|2 = 18 dB typ (f = 1 GHz, VCE = 5 V) MCH4015: |S21e|2 = 17 dB typ (f = 1 GHz, VCE = 5 V) • Low Noise: NF = 1.2 dB typ (f = 1 GHz, VCE = 1 V) • Package: MCPH-4/SC-82AB

• High Cut-off Frequency: f T = 16 GHz • High Gain: |S21e|2 = 17.5 dB typ • Low Noise: NF = 1.2 dB typ (f = 1 GHz, VCE = 1 V) • Package MCPH-4/SC-82AB

Material

MCH4000 series demonstrates good performance with high gain characteristics, even under low electric current.

FR4

Thickness

400 mm

Conductor

Au

Condcutor Thickness VCE = 3 V, 1 GHz

20

4.7

Dielectric Loss Tangent

0.02 25.4 mm2

Forward Transfer Gain, |S21e|2 (dB)

MCH4020

Parameter

Symbol

Value

Unit

Voltage

VCC

2

V

Circuit Current

ICC

10.5

mA

15

10

Parameter MCH4015 MCH4020 Market A Market B

5

0

1

20 mm

Dielectric Constant Size MCH4015

TUNING

MCH4020 Features

10

100 Collector Current, IC (mA)

1.2 kΩ 220 pF

Value

Unit

Frequency

F

500

800

MHz

Power Gain

Gp

15.3

14.3

dB

Noise Figure

NF

1.35

1.42

dB

1K

12 kΩ

220 pF

Symbol

10 kΩ 56 nH

100 pF

82 pF

22 pF

MCH4020

8.2 nH

10 pF

RF IN

82 nH RF OUT DC IN

68 nH

MCH4020 Application ON Semiconductor

Page 43

HDMI, Display Port Four High Speed Pairs, Up to Six Additional Lines, Low Capacitance ESD + Common Mode Filters EMI8x42

D2+

Key Requirement

GND

• Differential Mode cutoff frequency >3 GHz for HDMI 2.0 • Common Mode Filtering

D2D1+

Features

GND

• 3.3 VRWM • Insertion loss < 2.5 dB @ 2.5 GHz • -30 dB attenuation @ 2.4 GHz • VCLAMP < 12 V @ 16 A TLP • > ±15 kV Contact Discharge • Available in 0.4P and 0.5P packages

D1EMI8x42

D0+ GND D0CLK+ GND CLKCEC HEC DATA SCL SDA GND 5V HTP_D

PROTECTION

NUP4114

Device

Pairs

CM Attenuation @ 2.4 GHz (–dB)

EMI8042 EMI8142 EMI4192

2 2 2

30 30 20

DM 3 dB Bandwidth (GHz) VCLAMP @ 16 A TLP 4 4 5

11.8 11.8 18

0 −2

−10

−3

−15

−4

dB (SCC21)

dB (SDD21)

XDFN-10 XDFN-10 WDFN-10

2.5 x 1.35 2.2 x 1.35 2.5 x 12.0

−5

m1

−5 −6 −7

−20 −25 −30 −35

−8

−40

−9

Page 44

Size (mm)

0

−1

−10

Package

1.E+06

1.E+07

1.E+08

1.E+09

1.E+10

−45 −50

1.E+06

1.E+07

1.E+08

1.E+09

1.E+10

FREQUENCY (Hz)

FREQUENCY (Hz)

Typical Differential Mode Attenuation vs. Frequency

Typical Common Mode Attenuation vs. Frequency Consumer Electronics Solutions

HDMI, Display Port Four High Speed Pairs, Up to Six Additional Interface Lines, Low Capacitance ESD • Cap < 0.5 pF

I/O 1

I/O 2

I/O . . . . . I/O I/O I/O 3 (N-2) (N-1) N

Features • 0.3 pF ESD protection • Flow through routing in high speed lines • Industry leading low clamping voltage HDMI Type-A Connector D2+

=

Capacitance (pF) Package

Device

Data Lines

ESD8104 ESD8118 ESD8040 NUP4114UPX NUP4114UCL NUP4114H

4 (TMDS) 8 (TMDS) 14 (TMDS + Low Speed + Power) 5 (4 Low Speed + Power) 5 (4 Low Speed + Power) 5 (4 Low Speed + Power)

ESD8040

2.5 x 1.0 3.2 x 1.2 5.5 x 1.5 1.6 x 1.6 2.0 x 2.1 3.0 x 2.75

D2+ GND D2D1+

D2D1+

GND

GND

D1-

D1-

D0+

D0+

GND

GND

D0-

D0-

CLK+

CLK+

GND

GND

CLK-

CLK-

CEC

CEC

N/C (or HEC_DAT - HDMI1.4)

HEC DATA

SCL

SCL

SDA

SDA

GND

GND

5V

5V

HPD (and HEC_DAT - HDMI1.4)

HPD

• MediaGuard fully integrated solution • Includes ethernet protection (HDMI1.4) • Backdrive current protection NUP4114

UDFN-10 UDFN-10 UDFN-18 SOT-563 SC-88 TSOP-6

HDMI Type-A Connector

GND ESD8118

0.3 0.3 0.3 0.5 0.5 0.5

Size (mm)

PROTECTION

Key Requirement

ESD8118

Top layer Other layer

ESD8040

Without ESD With ESD HDMI 2.0 Eye Diagram with and without ESD8104. 6 Gb/s ON Semiconductor

Page 45

USB 3.x Type A Connector Two SuperSpeed Pairs, One High Speed Pair, V CC , Low Capacitance ESD Protection Key Requirement • Cap < 0.7 pF • 0.35 pF • Flow through routing • Industry leading low clamping voltage versus competitors I/O 1

I/O 2

USB 3.0 Type A Connector

USB 3.0/3.1 Type A Connetcor StdA_SSTX+

Features

StdA_SSTX+

Vbus

Vbus

StdA_SSTX-

ESD8704

ESD8116

D-

D-

GND_DRAIN

I/O . . . . . I/O I/O I/O 3 (N-2) (N-1) N

ESD7L5.0 Top layer Other layer

GND_DRAIN

D+

D+

StdA_SSRX+

StdA_SSRX+

GND

GND

StdA_SSRX-

PROTECTION

Device ESD8704 ESD7L ESD8504 ESD8104 ESD8116 ESD8011 ESD8101 ESD8111 ESD8006

Without ESD

Page 46

StdA_SSRX-

ESD8704 — 0.35 pF, 2 Layer Routing (ESD8704; ESD7L5.0 for D+, D- Lines)

=

ESD8116 — 0.30 pF, 1 Layer Routing

Interface

Data Lines

Capacitance (pF)

Package

Size (mm)

USB 3.x USB 3.x USB 3.0 USB 3.0 USB 3.0 USB 3.x USB 3.x USB 3.x USB 3.0

2 Pair (Tx, Rx) 1 Pair (D+/-) 2 Pair (Tx, Rx) 2 Pair (Tx, Rx) 3 Pair (Tx, Rx, D+/-) Single Line Single Line Single Line 3 Pair (Tx, Rx, D+/-)

0.35 0.5 0.4 0.3 0.3 0.10 0.20 0.20 0.25

UDFN-10 SOT-723 UDFN-10 UDFN-10 UDFN-8 X3DFN-2 DSN-2 WLCSP-2 UDFN-8

2.5 x 1.0 1.2 x 1.2 2.5 x 1.0 2.5 x 1.0 2.0 x 1.2 0.62 x 0.32 0.43 x 0.23 0.6 x 0.3 3.3 x 1.0

USB 3.0 @ 5 Gb/s

StdA_SSTX-

With ESD


USB 2.0 One High Speed Pair, V CC , Low Capacitance ESD Protection Key Requirement

I/O 1 I/O 2 I/O 3 I/O 4

• Cap < 5 pF

Features • 0.35 - 3.0 pF • Multi-part solutions available • Industry leading low clamping voltage

Device NUP2114UPX NUP2114UCM NUP4114UPX NUP4114UCL NUP4114H ESD7L5.0 ESD8351MUT ESD8351P2T ESD9L5.0

VBUS D+ DGnd

USB Host Controller NUP2114 =

Data Lines

Capacitance (pF)

Package

Size (mm)

1 Pair (D+/-) + Vbus 1 Pair (D+/-) + Vbus 2 Pair (D+/-) + Vbus 2 Pair (D+/-) + Vbus 2 Pair (D+/-) + Vbus 2 1 1 1

0.8 0.8 0.5 0.5 0.5 0.5 0.37 0.37 0.5

SOT-553 TSOP-6 SOT-563 SC-88 TSOP-6 SOT-723 X3DFN-2 SOD-923 SOD-923

1.2 x 1.6 3.0 x 2.75 1.6 x 1.6 2.0 x 2.1 3.0 x 2.75 1.2 x 1.2 0.6 x 0.3 1.0 x 0.6 1.0 x 0.6

VBUS D+ DGnd USB Host Controller

NUP4114 VBUS D+ DGnd

PROTECTION

One High Speed Pair, V CC , Common Mode Filter + ESD Protection Key Requirement • Cap < 5 pF • Common Mode Filtering

Micro USB Connector

Features

GND

• 0.5 - 0.8 pF • Integrated EMI suppression with ESD protection • Industry leading low clamping voltage Device EMI2121

Pairs

Capacitance @ 2.5 V (pF)

1

0.9

EMI2121

D+ D-

CM Attenuation DM Bandwidth @ 800 MHz (–dB) F3dB (GHz) Package –25

2.5

ID

WQFN

VBUS

Size (mm)

Top layer Other layer

2.2 x 2.0 x 0.75 0 -5 -10

dB

-15 -20 -25 -30

USB 2.0 @ 480 Mb/s ON Semiconductor

-35 1.E+06

Suppresses Common Mode Noise Deeper than Competing Passive Solution

Common Mode

Differential Mode 1.E+07

1.E+08

1.E+09

Frequency

Page 47

Ethernet: 10/100BASE-T, 1000BASE-TX, and Gigabit Four Pairs, Low Capacitance Surge and ESD Protection The 1000BASE-T or Gigabit Ethernet interface operating at higher bitrates is susceptible to ESD strikes, cable-discharge events and lightning-induced transients. Our products help meet IEC 61000-4-5, GR-1089-CORE and other Standards.

Features

Typical Application TPOPA

1000BASE-T ETHERNET TRANSCEIVER

TPONA

C5

ALC03

TVS8818 C3

TPONC

C6

BLC03 8

TPOPC

B+ VDD

C+

RJ45

TPONB

TRANSFORMER

C2

8

TPOPB

1

VDD

C7

CLC03

TPOPD C4

TPOND

8

1

• Compatible with Gb Ethernet and beyond • Enhanced protection for downstream electronics • Accommodates operating transients above 3.3 V • Small form-factor allows integration into connectors

A+ VDD

1

Benefits

C1

8

1

• Line-to-line capacitance < 3 pF • Vclamp (25 A surge) < 11 V • IEC 61000-4-2 rating > 30 kV • No latching danger • Surge rating maintained to 125°C

D+ VDD

C8

DLC03

Line Side : LC03-6 (optional) Transformer Side: TVS8818 Protection against metallic (transverse) strikes

1

2

TVS8818

5

Voltage (V), Current (A)

4

30

RJ-45 Connector

PROTECTION

3

6 Flow Through Routing

7

25

8/20 μs Surge Current

15

ON Semiconductor

Voltage

10 5 0 -10

8

Competitor Voltage

20

0

10

20 30 Time (μs)

40

50

60

Line-to-Line Surge Surge Protection Devices

Device LC03-6 NSP4201 NSP8814 NSP8818 NUP4114H SRDA3.3 SRDA05

VDC Max (V) 6.7 5.0 3.0 3.0 5.0 3.3 5.0

Line Transient Max (V) 7.0 6.0 3.2 3.2 5.0 5.0 7.0

Surge IPP, 8/20 ms (A) 100 25 35 35 12* 25 23

Typical Line-Line Capacitance (pF) 8.0 1.5 1.5 1.5 0.4 4.0 5.0

ESD Contact Rating (kV) ±30 ±30 ±30 ±30 ±13 ±8 ±8

Package SOIC-8 TSOP-6 UDFN-8 UDFN-10 TSOP-6 SOIC-8 SOIC-8

* On Pin 5.

Page 48


Electronic Fuses for Motor, Pump, Relay, and In-Box LED 3 – 12 V Power Bus Hot Plug Protection Features • Low RDS(ON), high operating and trip currents (IOP, ITRIP) Enable/ • Overvoltage protection Fault • Precise ITRIP control • Slew rate control • Thermal shut-down • EN pin for synchronizing multiple eFuses • Outperforms poly-fuses: – Tighter spec tolerances – Lower resistance – Shorter trip-time – Superior repeatability • High efficiency with high current capability • eFuses in parallel achieve practically any desired level of IOP and ITRIP

VCC

Charge Pump

Enable

Source Thermal Shutdown

Current Limit

UVLO

Voltage Clamp

ILimit

dV/dt Control

Typical Feature Set for eFuse

dV/dt

GND

Fan Blade Aerodynamic Load Overcurrent / Overheat conditions

Voltage (V) Angular Vel. (RPM)

Transient Overshoot Suppression Vin

L-C Low Pass Filter

eFuse NISxxxx

Input Filter Capacitor

Nominal Current

DC Motor’s Noise Filter

Peak Current

eFuse Prevents Overcurrent

Typical Application Block Diagram

Current (A) / Torque (ft * lb)

DC Motor I/V Characteristics

Nominal Voltage (V)

Input Voltage (V)

Vclamp (V)

Continuous Current (A)

Trip Current (A)

RDS(ON) (mW)

Auto-Retry

Latch

Package

NIS5431

3.3

-0.6 to 14

3.85

5

Adjustable

35

3

3

WDFN-10

NIS5452

5

-0.6 to 14

5.85

5

Adjustable

35

3

3

WDFN-10

NIS5232

12

-0.6 to 18

15

4.2

Adjustable

44

**

3

DFN-10

NIS5820*

12

-0.3 to 22

14

8

Adjustable

24

3

3

WDFN-10

NIS5020*

12

-0.3 to 22

14

10

Adjustable

14

3

3

WDFN-10

NIS5021*

12

-0.3 to 22

14

12

Adjustable

14

3

3

WDFN-10

Device

* Pending 1Q18. ** Auto-retry available on NIS5132MN2.

ON Semiconductor

Page 49

PROTECTION

Permanent Magnet DC motor

Power Protection Surge and Over-Voltage Protection Switches Features

Legacy USB/ USB Type-C Connector

• Optimized for Input Power Stage with USB-C • 100 V Surge Capable Integrated TVS • Low RON for Low Power Loss • Fast Over Voltage Response Time • Design Flexibility with Adjustable/Selectable OVP • Reverse Current Block • Compact Packages, WLCSP and DFN

FPF2281

Travel Adapter

1 μF

IN

1 μF

OUT

R1 OVLO #EN

R2

HV Battery Charger

Processor

#ACOK RPU

GND

VIO

Over Voltage Protection Switches Channel

VIN Min (V)

VIN Max (V)

OVP (V)

RON (mW)

IOUT Max (A)

FPF2280

Single

2.5

28

6.8*

30 @ 5.0 V

4.5

FPF2281

Single

2.5

28

14*

30 @ 5.0 V

4.5

FPF2290

Single

2.5

28

SEL**

30 @ 5.0 V

4.5

FPF2498

Single

3.5

28

6.5

80 @ 5.0 V

1.75

NCP398

Single

2.9

28

5.65

190 @ 5.0 V

FPF3488

SIDO***

2.7

28

13.9

28 @ 5.0 V

FPF3042

DISO^

4

18

14

FPF3695^^

Single

1.2

28

OPN^^^

NCP367

Single

1.2

28

OPN^^^

50 @ 3.5 V

Device

Integrated TVS Discharge Path Yes

Package

No

WLCSP-12

Yes

No

WLCSP-12

Yes

No

WLCSP-12

No

No

WLCSP-6

0.8

No

Yes

WLCSP-4

3.5

Yes

No

WLCSP-28

70 @ 5.0 V

2.7

No

No

WLCSP-16

50 @ 3.5 V

3.4

No

No

WLCSP-40

3.4

No

No

DFN-8

PROTECTION

* Default but Adjustable w/ external R. ** Selectable w/ Logic Pins. *** Single Input Dual Output. ^ Dual Input Single Output. ^^ Pending 2Q17. ^^^ By Option.

Over Current Protection Switches Features

VIO

Battery

• Optimized for 5V USB-OTG and VCONN with USB-C • Fast Over Current Response Time • Design Flexibility with Adjustable Current Limit Set • True Reverse Current Block • Compact Packages, WLCSP and DFN • UL Certified

5V Boost

FPF2595 CIN

Vin

Vout

ON

OC_FLAGB

ISET

AP

COUT

USB Connector

OTG Device

GND

Over Current Protection Switches Channel

VIN Min (V)

VIN Max (V)

RON (mW)

ILIM Range (A)

OVP

RCB*

Package

FPF2195

Single

1.8

5.5

55 @ 3.3 V

0.1 ~ 1.5

No

Yes

WLCSP-6

FPF2495

Single

2.5

5.5

70 @ 5.0 V

0.05 ~ 2.0

Yes

Yes

WLCSP-9

FPF2496

Single

3.5

5.5

70 @ 5.0 V

0.1 ~ 2.5

Yes

Yes

WLCSP-9

FPF2595

Single

2.5

5.5

35 @ 5.0 V

0.1 ~ 3.5

Yes

Yes

WLCSP-12

FPF2895

Single

4

22

27 @ 5.0 V

0.5 ~ 5.0

Yes

Yes

WLCSP-24

NCP380

Single

2.5

5.5

55 @ 5.0 V

0.5 ~ 2.1

No

Yes

UDFN-6

NCP382

SIDO**

2.5

5.5

80 @ 5.0 V

Fixed***

No

Yes

DFN-8

NCP383

SIDO**

2.7

5.5

45 @ 5.0 V

0.5 ~ 2.8

No

Yes

UDFN-10

Device

* Reverse Current Block. ** Single Input Dual Output. *** By Option.

Page 50


Switching Controllers NCP3011 Key Features

VIN

• Wide input voltage range • Buffered external +1.25 V reference • PowerGood + Enable/Disable pins • External synchronization • Output overvoltage and undervoltage protection

VCC BST

NCP3011 EN

HSDR

PG

VSW

NTMD4840 LO

VREF

LSDR

SYNC

GND

COMP

VOUT

FB

fSW (kHz)

Device

Vin Min Vin Max (V) (V)

Vout Max (V)

Comments

Package

NCP1587

250-300

4.5

13.2

Down to 0.8

1 A drive capability; short circuit protection

SOIC-8

NCP1589D

300/600

4.5

13.2

Down to 0.8

Light load efficiency

SOIC-8

NCP5425

150-750

4.5

13.2

Down to 0.8

Dual output

TSSOP-20

CS51031

200-700

4.5

16

Down to 1.25

No compensation required; PFET

SOIC-8

NCP3011

400

4.7

28

Down to 0.8

PG, EN, SYNC features

TSSOP-14

NCP3020

300/600

4.7

28

Down to 0.6

Ceramic output capacitors

SOIC-8

NCP3030

1200/2400

4.7

28

Down to 0.6

High switching frequency

SOIC-8

40-300

7

40

External Adj.

Buck, boost, forward, flyback

SOIC-16, PDIP-16

LV5747QA

385

8

42

Down to 0.7

Current mode buck; fixed frequency; soft start; EN

VQFN-16J

LV5749NV

80-500

8.5

42

Down to 0.67 Current mode buck; double OCP function; variable frequency; soft start; EN

SSOP-16

LV5769V

80-500

8.5

42

Down to 0.67

Current mode buck; variable frequency; soft start; EN

SSOP-16

LV5762QA

1000

8

42

Down to 0.7

Current mode buck; fixed high frequency; soft start; EN

VQFN-16J

LV5725JA

50-500

4.5

50

Down to 0.7

Current mode buck; soft start; hiccup; programmable current limit; SYNC; PGOOD

SSOP-16

CS5124

400

7.7

75

External Adj.

Small PCB footprint; isolated

SOIC-8

NCP1034

Up to 500

8

100

Down to 1.25

2 A drive capability; synchronization

SOIC-16

NCP1030

300

10

200

2.5 up to Vin

PoE applications; integrated switch

Micro8

NCP1031

300

10

200

2.5 up to Vin

PoE applications; integrated switch

SOIC-8, DFN-8

TL594

ON Semiconductor

Page 51

POWER MANAGEMENT

Switching Controllers

Linear and Switching Regulators Linear & Switching Regulators for Current of 5 A Type Switching Regulator Page 52

Device MC34167

Iout (A)

fSW (kHz)

Vin Min (V)

Vin Max (V)

Comments

Package

5.0

72

7

40

Standby mode