Ranges - pdfstream.manualsonline.com

6 downloads 398 Views 1MB Size Report
Be sure the drip pans and the vent duct are ...... Please provide your e-mail address to receive, via e-mail, discounts,
Electric

Ranges Safety Information . . . . . . . . 2–6 Operating Instructions Adjust the Oven Thermostat . . . . . . . . . . . . . . . .21 Clock and Timer . . . . . . . . .15, 16 Oven . . . . . . . . . . . . . . . . . . .12–14 Oven Controls . . . . . . . . . . .10, 11 Sabbath Feature . . . . . . . . . .19, 20 Selecting Types of Cookware . . .9 Self-Cleaning . . . . . . . . . . . .22, 23 Special Features . . . . . . . . . . . . .18 Surface Units . . . . . . . . . . . . . 7, 8 Timed Baking and Roasting . . .17 Write the model and serial numbers here: Model # ______________________ Serial # ______________________ You can find them on a label, behind the storage drawer on the oven frame.

Care and Cleaning . . . . . . 22–30 Glass Cooktop . . . . . . . . . . .29, 30 Self-Cleaning Oven . . . . . . .22, 23

Installation Instructions Anti-Tip Device . . . . . . . . . .31, 37 Before You Begin . . . . . . . . . . . 31 Electrical Connections . . . .33–36 Leveling . . . . . . . . . . . . . . . . . . .37

Troubleshooting Tips . . . . 39–43 Accessories . . . . . . . . . . . . . . . . 44 Consumer Support Consumer Support . . .Back Cover Product Registration . . . . . 45, 46 Warranty . . . . . . . . . . . . . . . . . . 47

Owner’s Manual and Installation Instructions www.AmericanaAppliances.com

Printed in Mexico Printed on Recycled Paper

Model ABS300

183D6379P029

49-88023

11-05 JR

Safety Instructions

IMPORTANT SAFETY INFORMATION. READ ALL INSTRUCTIONS BEFORE USING.

WARNING!

For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric shock, or to prevent property damage, personal injury, or loss of life.

WARNING ANTI-TIP DEVICE Operating Instructions

All ranges can tip and injury could result. To prevent accidental tipping of the range, attach it to the wall by installing the Anti-Tip device supplied. If the Anti-Tip device supplied with the range does not fit this application, use the universal Anti-Tip device WB2X7909.

Care and Cleaning

To check if the device is installed and engaged properly, carefully tip the range forward. The Anti-Tip device should engage and prevent the range from tipping over.

Please refer to the Anti-Tip device information in this manual. Failure to take this precaution could result in tipping of the range and injury.

IMPORTANT SAFETY NOTICE The California Safe Drinking Water and Toxic Enforcement Act requires the Governor of California to publish a list of substances known to the state to cause cancer, birth defects or other reproductive harm, and requires businesses to warn customers of potential exposure to such substances.

Installation Instructions Consumer Support Troubleshooting Tips

If you pull the range out from the wall for any reason, make sure the device is properly engaged when you push the range back against the wall. If it is not, there is a possible risk of the range tipping over and causing injury if you or a child stand, sit or lean on an open door.

2

The fiberglass insulation in self-clean ovens gives off a very small amount of carbon monoxide during the cleaning cycle. Exposure can be minimized by venting with an open window or using a ventilation fan or hood.

SAFETY PRECAUTIONS When using electrical appliances, basic safety precautions should be followed, including the following: ■ Use this appliance only for its intended purpose as described in this Owner’s Manual.

■ Do not attempt to repair or replace any part of your range unless it is specifically recommended in this manual. All other servicing should be referred to a qualified technician.

■ Do not store flammable materials in an oven or near the cooktop. ■

Care and Cleaning

■ Before performing any service, disconnect the range power supply at the household distribution panel by removing the fuse or switching off the circuit breaker.

■ Do not allow anyone to climb, stand or hang on the door, storage drawer, or cooktop. They could damage the range and even tip it over, causing severe personal injury.

Operating Instructions

■ Be sure your appliance is properly installed and grounded by a qualified technician in accordance with the provided installation instructions.

■ Do not leave children alone---children should not be left alone or unattended in an area where an appliance is in use. They should never be allowed to sit or stand on any part of the appliance.

Safety Instructions

www.AmericanaAppliances.com

CAUTION: Items of interest to

children should not be stored in cabinets above a range or on the backsplash of a range—children climbing on the range to reach items could be seriously injured.

COOK MEAT AND POULTRY THOROUGHLY… Installation Instructions

Cook meat and poultry thoroughly—meat to at least an INTERNAL temperature of 160°F and poultry to at least an INTERNAL temperature of 180°F. Cooking to these temperatures usually protects against foodborne illness.

Troubleshooting Tips Consumer Support

3

WARNING! SAFETY PRECAUTIONS ■ Never wear loose-fitting or hanging garments while using the appliance. Be careful when reaching for items stored over the range. Flammable material could be ignited if brought in contact with hot surface units or heating elements and may cause severe burns.

Operating Instructions

Safety Instructions

IMPORTANT SAFETY INFORMATION. READ ALL INSTRUCTIONS BEFORE USING.

■ Use only dry pot holders---moist or damp pot holders on hot surfaces may result in burns from steam. Do not let pot holders touch hot surface units or heating elements. Do not use a towel or other bulky cloth.

Care and Cleaning

■ For your safety, never use your appliance for warming or heating the room. ■ Do not let cooking grease or other flammable materials accumulate in or near the range. ■ Do not use water on grease fires. Never pick up a flaming pan. Turn the controls off. Smother a flaming pan on a surface unit by covering the pan completely with a wellfitting lid, cookie sheet or flat tray. Use a multi-purpose dry chemical or foam-type fire extinguisher.

■ Potentially hot surfaces include the cooktop, areas facing the cooktop, oven vent opening, surfaces near the opening, crevices around the oven door and metal trim parts above the door. ■ REMEMBER: The inside surface of the oven may be hot when the door is opened. ■ Do not store or use combustible materials, gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. ■ Keep the hood and grease filters clean to maintain good venting and to avoid grease fires.

■ Flaming grease outside a pan can be put out by covering it with baking soda or, if available, by using a multi-purpose dry chemical or foam-type fire extinguisher.

Installation Instructions Consumer Support Troubleshooting Tips

■ Do not touch the surface units, the heating elements or the interior surface of the oven. These surfaces may be hot enough to burn even though they are dark in color. During and after use, do not touch, or let clothing or other flammable materials contact, the surface units, areas nearby the surface units or any interior area of the oven; allow sufficient time for cooling first.

■ Flame in the oven can be smothered completely by closing the oven door and turning the oven off or by using a multipurpose dry chemical or foam-type fire extinguisher.

OVEN ■ Stand away from the range when opening the oven door. Hot air or steam which escapes can cause burns to hands, face and/or eyes.

■ Pulling out the shelf to the stop-lock is a convenience in lifting heavy foods. It is also a precaution against burns from touching hot surfaces of the door or oven walls.

■ Do not heat unopened food containers. Pressure could build up and the container could burst, causing an injury.

■ When using cooking or roasting bags in the oven, follow the manufacturer’s directions.

■ Keep the oven vent unobstructed. ■ Keep the oven free from grease buildup. ■ Place the oven shelf in the desired position while the oven is cool. If shelves must be handled when hot, do not let pot holder contact the heating elements.

4

■ Do not use the oven to dry newspapers. If overheated, they can catch on fire. ■ Do not use the oven for a storage area. Items stored in an oven can ignite. ■ Do not leave paper products, cooking utensils or food in the oven when not in use.

SELF-CLEANING OVEN (on some models) ■ Do not clean the door gasket. The door gasket is essential for a good seal. Care should be taken not to rub, damage or move the gasket.

■ If the self-cleaning mode malfunctions, turn the oven off and disconnect the power supply. Have it serviced by a qualified technician. ■ Take the shelves out of the oven before you begin the self-clean cycle or they may discolor.

Care and Cleaning

■ Do not use oven cleaners on self-clean models. No commercial oven cleaner or oven liner protective coating of any kind should be used in or around any part of the oven. Residue from oven cleaners will damage the inside of the oven when the self-clean cycle is used.

■ Be sure to wipe up excess spillage before starting the self-cleaning operation.

Operating Instructions

■ Clean only parts listed in this Owner’s Manual.

■ Before self-cleaning the oven, remove the broiler pan, grid and other cookware.

SURFACE UNITS–ALL MODELS Use proper pan size–select cookware having flat bottoms large enough to cover the surface unit heating element. The use of undersized cookware will expose a portion of the surface unit to direct contact and may result in ignition of clothing. Proper relationship of cookware to surface unit will also improve efficiency.

■ Only certain types of glass, glass ⁄ceramic, earthenware or other glazed containers are suitable for cooktop service; others may break because of the sudden change in temperature.

■ Always turn the surface units off before removing cookware. ■ Do not flame foods on the cooktop. If you do flame foods under the hood, turn the fan on.

■ Foods for frying should be as dry as possible. Frost on frozen foods or moisture on fresh foods can cause hot fat to bubble up and over the sides of the pan. ■ Use little fat for effective shallow or deep fat frying. Filling the pan too full of fat can cause spillovers when food is added. ■ If a combination of oils or fats will be used in frying, stir together before heating, or as fats melt slowly. ■ Always heat fat slowly, and watch as it heats. ■ Use a deep fat thermometer whenever possible to prevent overheating fat beyond the smoking point.

5

Troubleshooting Tips Consumer Support

■ To minimize the possibility of burns, ignition of flammable materials and spillage, the handle of a container should be turned toward the center of the range without extending over nearby surface units.

■ Keep an eye on foods being fried at high or medium high heat settings.

Installation Instructions

■ Never leave the surface units unattended at high heat settings. Boilovers cause smoking and greasy spillovers that may catch on fire.

Safety Instructions

www.AmericanaAppliances.com

WARNING! RADIANT SURFACE UNITS (on some models) Use care when touching the cooktop. The glass surface of the cooktop will retain heat after the controls have been turned off. ■ Avoid scratching the glass cooktop. The cooktop can be scratched with items such as sharp instruments, rings or other jewelry and rivets on clothing.

Operating Instructions

Safety Instructions

IMPORTANT SAFETY INFORMATION. READ ALL INSTRUCTIONS BEFORE USING.

■ Large scratches or impacts to glass doors or cooktops can lead to broken or shattered glass.

Care and Cleaning

■ Do not operate the radiant surface units if the glass is broken. Spillovers or cleaning solution may penetrate a broken cooktop and create a risk of electrical shock. Contact a qualified technician immediately should your glass cooktop become broken. ■ Never use the glass cooktop surface as a cutting board. ■ Do not place or store items that can melt or catch fire on the glass cooktop, even when it is not being used.

Installation Instructions

■ Be careful when placing spoons or other stirring utensils on the glass cooktop surface when it is in use. They may become hot and could cause burns.

■ Clean the cooktop with caution. If a wet sponge or cloth is used to wipe spills on a hot surface unit, be careful to avoid steam burns. Some cleaners can produce noxious fumes if applied to a hot surface. NOTE: We recommend that you avoid wiping any surface unit areas until they have cooled and the indicator light has gone off. Sugar spills are the exception to this. Please see Cleaning the glass cooktop section. ■ When the cooktop is cool, use only the recommended cleaning cream to clean the cooktop. ■ To avoid possible damage to the cooking surface, do not apply cleaning cream to the glass surface when it is hot. ■ After cleaning, use a dry cloth or paper towel to remove all cleaning cream residue. ■ Read and follow all instructions and warnings on the cleaning cream labels. ■ Do not lift the cooktop. Lifting the cooktop can lead to damage and improper operation of the range.

WARNING!

Consumer Support Troubleshooting Tips

COIL SURFACE UNITS (on some models) ■ Clean the cooktop with caution. If a wet sponge is used to wipe spills on a hot cooktop, be careful to avoid steam burns. ■ To avoid the possibility of a burn or electric shock, always be certain that the controls for all surface units are at the OFF position and all coils are cool before attempting to lift or remove a unit. ■ Do not immerse or soak the removable surface units. Do not put them in a dishwasher.

■ Be sure the drip pans and the vent duct are not covered and are in place. Their absence during cooking could damage range parts and wiring. ■ Do not use aluminum foil to line the drip pans or anywhere in the oven except as described in this manual. Misuse could result in a shock, fire hazard or damage to the range.

READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY. SAVE THESE INSTRUCTIONS 6

www.AmericanaAppliances.com

Throughout this manual, features and appearance may vary from your model.

How to Set Push the knob in and turn in either direction to the setting you want.

At both OFF and HI the control clicks into position. You may hear slight clicking sounds during cooking, indicating the control is keeping the power level you set.

Safety Instructions

Using the surface units.

Operating Instructions

Be sure you turn the control knob to OFF when you finish cooking.

A HOT SURFACE indicator light will glow when any radiant element is turned on, and will remain on until the surface is cool enough to touch. A SURFACE UNIT on indicator light will glow when any surface unit is on. NOTE: The SURFACE UNIT on indicator light may glow between the surface control settings of LO and OFF, but there is no power to the surface units.

Care and Cleaning

Indicator Lights (on radiant glass models only)

Installation Instructions Troubleshooting Tips Consumer Support

7

Safety Instructions Operating Instructions Care and Cleaning Installation Instructions Consumer Support Troubleshooting Tips

Using the radiant surface units. (on some models) About the radiant surface units… SURFACE

COOKING ;;;;;;;;;;;;; ;;;;;;;;;;;; ; ;;;; ;;; ;; ;;;;;;;;

Never cook directly on the glass. Always use cookware.

OFF CENTER ;;;;;;;;;;; ;;;;;;;;;;; ; ;;;; ;;; ;;;;;;;;;;; ; ;;;; ;;; Always place the pan in;the center of

The radiant cooktop features heating units beneath a smooth glass surface. NOTE: A slight odor is normal when a new cooktop is used for the first time. It is caused by the heating of new parts and insulating materials and will disappear in a short time. The surface unit will cycle on and off to maintain your selected control setting. It is safe to place hot cookware from the oven or surface on the glass surface when the surface is cool.

■ Water stains (mineral deposits) are removable using the cleaning cream or full-strength white vinegar. ■ Use of window cleaner may leave an iridescent film on the cooktop. The cleaning cream will remove this discoloration. ■ Don’t store heavy items above the cooktop. If they drop onto the cooktop, they can cause damage. ■ Do not use the surface as a cutting board.

Even after the surface units are turned off, the glass cooktop retains enough heat to continue cooking. To avoid over-cooking, remove pans from the surface units when the food is cooked. Avoid placing anything on the surface unit until it has cooled completely.

the surface unit you are cooking on.

DRAGGING ; ; ; ;;;;;;;;;;;; ; ;;;; ;;; ;;;;;;;;;;; ;;;;;;;;;;;; ; ;

Do not slide cookware across the cooktop because it can scratch the glass—the glass is scratch resistant, not scratch proof.

Temperature Limiter Every radiant surface unit has a temperature limiter.

The temperature limiter may cycle the units off for a time if:

The temperature limiter protects the glass cooktop from getting too hot.

■ The pan boils dry. ■ The pan bottom is not flat. ■ The pan is off center. ■ There is no pan on the unit.

8

www.AmericanaAppliances.com

The following information will help you choose cookware which will give good performance on glass cooktops.

Stainless Steel:

Glass-ceramic:

recommended

usable, but not recommended Poor performance. May scratch the surface.

Aluminum:

Stoneware:

Copper Bottom:

Make sure the canner is flat on the bottom.

Home Canning Tips: Be sure the canner is centered over the surface unit.

Use recipes and procedures from reputable sources. These are available from manufacturers such as Ball® and Kerr® and the Department of Agriculture Extension Service.

Care and Cleaning

recommended Copper may leave residues which can appear as scratches. The residues can be removed, as long as the cooktop is cleaned immediately. However, do not let these pots boil dry. Overheated metal can bond to glass cooktops. An overheated copper bottom pot will leave a residue that will permanently stain the cooktop if not removed immediately.

usable, but not recommended Poor performance. May scratch the surface.

To prevent burns from steam or heat, use caution when canning.

Porcelain Enamel Covered Cast Iron: recommended As long as the cookware is covered completely with porcelain enamel, this cookware is recommended. Caution is recommended for cast-iron cookware that is not completely covered with smooth porcelain enamel, as it may scratch the glass-ceramic cooktop.

Installation Instructions

Pans with rounded, curved, ridged or warped bottoms are not recommended.

Operating Instructions

Check pans for flat bottoms by using a straight edge.

heavy weight recommended Good conductivity. Aluminum residues sometimes appear as scratches on the cooktop, but can be removed if cleaned immediately. Because of its low melting point, thin-weight aluminum should not be used.

Safety Instructions

Selecting types of cookware.

The following information will help you choose cookware which will give good performance on coil cooktops.

1″

Not over 1 inch

Use medium- or heavy-weight cookware. Aluminum cookware conducts heat faster than other metals. Cast-iron and coated cast-iron cookware are slow to absorb heat, but generally cook evenly at low to medium heat settings. Steel pans may cook unevenly if not combined with other metals.

For best cooking results, pans should be flat on the bottom. Match the size of the saucepan to the size of the surface unit. The pan should not extend over the edge of the surface unit more than 1 inch.

Wok Cooking We recommend that you use only a flat-bottomed wok. They are available at your local retail store. Do not use woks that have support rings. Use of these types of woks, with or without the ring in place, can be dangerous. Use only flat-bottomed woks.

Placing the ring over the surface unit will cause a buildup of heat that will damage the porcelain cooktop. Do not try to use such woks without the ring. You could be seriously burned if the wok tips over.

9

Troubleshooting Tips Consumer Support

Surface Cookware Tips

Safety Instructions

Using the oven controls. (on some models) Throughout this manual, features and appearance may vary from your model.

Operating Instructions

or

Care and Cleaning

or

Oven Control, Clock and Timer Features and Settings BAKE/TEMP RECALL Pad Touch this pad to select the bake function.

BAKE Light Flashes while in edit mode—you can change the oven temperature at this point. Glows when the oven is in bake mode.

Installation Instructions Consumer Support Troubleshooting Tips

Touch this pad to select the timer feature. Then touch the + and – pads to adjust the timer.

TIMER Light

Must be touched to start any cooking or cleaning function.

Flashes while in edit mode—you can change the set time at this point. Glows when the timer has been activated. Flashes again when the time has run out until the control is reset.

Display

CLOCK Pad

START/ON Pad

Shows the time of day, oven temperature, whether the oven is in the bake, broil or self-cleaning mode and the times set for the timer or automatic oven operations. The display will show PRE while preheating. When the oven reaches the selected temperature, the oven control will beep and the display will show the oven temperature.

10

KITCHEN TIMER ON/OFF or TIMER ON/OFF Pad

To set the clock, press this pad twice and then press the + and – pads. The time of day will flash in the display when the oven is first turned on.

START TIME Pad (on some models) Use along with the COOKING TIME or SELF CLEAN pads to set the oven to start and stop automatically at a time you set.

If “F– and a number or letter” flash in the display and the oven control signals, this indicates a function error code.

START TIME Light

If your oven was set for a timed oven operation and a power outage occurred, the clock and all programmed functions must be reset.

Flashes while in edit mode—you can change the start time at this point. Glows when the function has been activated.

The time of day will flash in the display when there has been a power outage. Reset the clock.

COOKING TIME Pad (on some models) Touch this pad and then touch the + or – pads to set the amount of time you want your food to cook. The oven will shut off when the cooking time has run out.

If the function error code appears during the self-cleaning cycle, check the oven door latch. The latch handle may have been moved, even if only slightly, from the latched position. Make sure the latch is moved to the right as far as it will go.

COOKING TIME Light

Touch the CLEAR/OFF pad. Allow the oven to cool for one hour. Put the oven back into operation. If the function error code repeats, disconnect the power to the range and call for service.

Flashes while in edit mode—you can change the set time at this point. Glows when the function has been activated. Flashes again when the time has run out until the control is reset.

Oven Control, Clock and Timer Features and Settings Indicator Lights (on some pads)

This lights anytime the oven has been programmed using the COOKING TIME or START TIME functions.

EDIT mode lasts several seconds after the last pad press. START TIME ON/OFF and COOKING TIME ON/OFF will be the only pads lit if either of these options is selected. (Example: START TIME is selected with BAKE—the START TIME pad will remain lit until the clock reaches the programmed time, at which point it will turn off and the BAKE/TEMP RECALL pad light will light up).

OVEN LIGHT or

Pad

Touch this pad to turn the oven light on or off.

– Pad Short taps to this pad will decrease the time or temperature by small amounts. Touch and hold the pad to decrease the time or temperature by larger amounts.

Operating Instructions

AUTOMATIC OVEN Light (on some models)

Safety Instructions

www.AmericanaAppliances.com

+ Pad

Care and Cleaning

Short taps to this pad will increase the time or temperature by small amounts. Touch and hold the pad to increase the time or temperature by larger amounts.

SELF CLEAN Pad Touch this pad to select the self-cleaning function. See the Using the self-cleaning oven section.

CLEAN Light

Installation Instructions

Flashes while in edit mode—you can change the length of time for the self-clean cycle at this point. Glows when the oven is in the self-clean cycle. After the self-clean cycle, the light will turn off. Unlatch the door.

CLEAR/OFF Pad Touch this pad to cancel ALL oven operations except the clock and timer.

BROIL HI/LO Pad Touch this pad to select the broil function. Flashes while in edit mode—you can switch from HI to LO BROIL at this point. Glows when the oven is in broil mode.

11

Troubleshooting Tips Consumer Support

BROIL Light

Safety Instructions

Using the oven. Clock and Kitchen Timer (on some models) KITCHEN TIMER ON/OFF Pad Touch this pad to select the timer feature.

CLOCK Pad Touch this pad before setting the clock.

Display

Operating Instructions

Shows the time of day and the time set for the timer, cook time or start time. Appearance may vary.

These pads allow you to set the clock and timer.

Oven Temperature Knob (on some models) Turn this knob to the setting you want. ■ The oven cycling light glows until the oven reaches your selected temperature, then goes off and on with the oven element(s) during cooking.

Care and Cleaning Installation Instructions Consumer Support Troubleshooting Tips

SET +/- Pads

Before you begin… To avoid possible burns, place the shelves in the desired position before you turn the oven on.

The oven has 5 shelf positions. It also has a special low shelf position (R) for extra large items, such as a large turkey.

The shelves have stop-locks, so that when placed correctly on the shelf supports (A through E), they will stop before coming completely out, and will not tilt. When placing and removing cookware, pull the shelf out to the bump on the shelf support.

To remove a shelf, pull it toward you, tilt the front end up and pull it out. To replace, place the end of the shelf (stoplocks) on the support, tilt up the front and push the shelf in. NOTE: The shelf is not designed to slide out at the special low shelf (R) position.

How to Set the Oven for Baking or Roasting (on models without an oven temperature knob) Touch the BAKE pad. Touch the + or – pads until the desired temperature is displayed. Touch the START/ON pad.

The oven has a special low shelf (R) position just above the oven bottom. Use it when extra cooking space is needed, for example, when cooking a large turkey. The shelf is not designed to slide out at this position.

12

The oven will start automatically. The display will show PRE while preheating. When the oven reaches the selected temperature, the oven control will beep and the display will show the oven temperature. To change the oven temperature during BAKE cycle, touch the BAKE pad and then the + or – pads to get the new temperature.

Check food for doneness at minimum time on recipe. Cook longer if necessary. Touch the CLEAR/OFF pad when baking is finished and then remove the food from the oven.

Type of Food

Shelf Position

Frozen pies (on cookie sheet)

C

Angel food cake, bundt or pound cakes

B

Biscuits, muffins, brownies, cookies, cupcakes, layer cakes, pies

B or C

Casseroles

B or C

Turkey

R or A

Roasting

R, A or B

Preheating and Pan Placement Preheat the oven if the recipe calls for it. To preheat, set the oven at the correct temperature. Preheating is necessary for good results when baking cakes, cookies, pastry and breads.

On some models, the display will show “PRE” while preheating. When the oven reaches the selected temperature, the oven control will beep and the display will show the oven temperature.

Operating Instructions

For ovens without a preheat indicator light or tone, preheat 10 minutes.

Baking results will be better if baking pans are centered in the oven as much as possible. Pans should not touch each other or the walls of the oven. If you need to use two shelves, stagger the pans so one is not directly above the other, and leave approximately 11⁄2″ from the front of the pan to the front of the shelf.

Safety Instructions

www.AmericanaAppliances.com

Aluminum Foil

Cut slits in the foil just like the grid.

You can use aluminum foil to line the broiler pan and broiler grid. However, you must mold the foil tightly to the grid and cut slits in it just like the grid.

Aluminum foil may also be used to catch a spillover. To do so, place a small sheet of foil on a lower shelf several inches below the food. Never entirely cover a shelf with aluminum foil. This will disturb the heat circulation and result in poor baking.

Care and Cleaning

Never cover the oven bottom with aluminum foil.

How to Set the Oven for Broiling (on models without an oven temperature knob)

Follow suggested shelf positions in the Broiling Guide. Leave the door open to the broil stop position. The door stays open by itself, yet the proper temperature is maintained in the oven.

Touch the START/ON pad. When broiling is finished, touch the CLEAR/OFF pad.

If your range is connected to 208 volts, rare steaks may be broiled by preheating the broiler and positioning the oven shelf one position higher.

Touch the BROIL HI/LO pad once for HI Broil. To change to LO Broil, touch the BROIL HI/LO pad again.

13

Troubleshooting Tips Consumer Support

Use LO Broil to cook foods such as poultry or thick cuts of meat thoroughly without over-browning them.

Installation Instructions

Place the meat or fish on the broiler grid in the broiler pan.

Safety Instructions Operating Instructions

Broiling Guide The size, weight, thickness, starting temperature and your preference of doneness will affect broiling times. This guide is based on meats at refrigerator temperature. † The U.S. Department of Agriculture says “Rare beef is popular, but you should know that cooking it to only 140°F. means some food poisoning organisms may survive.” (Source: Safe Food Book. Your Kitchen Guide. USDA Rev. June 1985.)

Consumer Support Troubleshooting Tips

Food Ground Beef

Quantity and/ or Thickness

Shelf* First Side Second Side Position Time (min.) Time (min.) Comments

1 lb. (4 patties) ⁄ to 3⁄4″ thick 4 lbs. (12 patties)

C

10

7–10

C

15

11

34

⁄ to 1″ thick 1 to 1 1⁄2 lbs.

E D D

6 8 10

4 6 7–10

1 1⁄2″ thick 2 to 2 1⁄2 lbs.

C C D B

10 15 20 25

8 10–12 20 25

B

25

15

Beef Steaks Rare† Medium Well Done Rare† Medium Well Done Chicken

1 whole cut up 2 to 2 1⁄2 lbs., split lengthwise Breast

Bakery Product Bread (toast) English Muffin

2 to 4 slices 2 (split)

D E

3 3-4

1

Lobster Tails

2–4

B

18–20

Do not turn over.

Fish Fillets

1 lb. (1⁄4 to 1⁄2″ thick)

D

5

5

2 (1″ thick) 2 (1⁄2 to 3⁄4″ thick) 1⁄2″ thick 1″ thick 2 (1⁄2″ thick) 2 (1″ thick) about 1 lb.

D D C C C C

10 10 6 8 10 15

5 6 8 10 15

2 (1″ thick) about 10 to 12 oz. 2 (11⁄2″ thick) about 1 lb.

D D D D

7 10 9 14

4 9 6 10

Salmon Steaks Fillets Ham Slices (precooked) Pork Chops Well Done Lamb Chops Medium Well Done Medium Well Done

*See illustration for description of shelf positions.

14

Space evenly.

12

The oven has 5 shelf positions.

Installation Instructions

Care and Cleaning

Using the oven.

Steaks less than 3⁄4″ thick are difficult to cook rare. Slash fat.

Brush each side with melted butter. Broil skin-side-down first. Space evenly. Place English muffins cutside-up and brush with butter if desired. Cut through back of shell. Spread open. Brush with melted butter before broiling and after half of broiling time. Handle and turn very carefully. Brush with lemon butter before and during cooking, if desired. Turn carefully. Do not turn skin side down.

Slash fat.

Slash fat.

www.AmericanaAppliances.com

Not all features are on all models.

To Set the Clock The clock must be set to the correct time of day for the automatic oven timing functions to work properly. The time of day cannot be changed during a timed baking or self-cleaning cycle.

Touch the + or – pads.

Make sure the clock is set to the correct time of day.

To check the time of day when the display is showing other information, simply touch the CLOCK pad. The time of day shows until another pad is touched.

If the + or – pads are not touched within one minute after you touch the CLOCK pad, the display reverts to the original setting. If this happens, touch the CLOCK pad and reenter the time of day.

If you have several clocks in your kitchen, you may wish to turn off the time of day clock display on your range.

Touch the CLOCK pad again to recall the clock display.

Touch the CLOCK pad once to turn off the time of day display. Although you will not be able to see it, the clock maintains the correct time of day.

or

The timer does not control oven operations. The maximum setting on the timer is 9 hours and 59 minutes. Touch the KITCHEN TIMER ON/OFF or TIMER ON/OFF pad.

When the timer reaches :00, the control will beep 3 times followed by one beep every 6 seconds until the KITCHEN TIMER ON/OFF or TIMER ON/OFF pad is touched.

If you make a mistake, touch the KITCHEN TIMER ON/OFF or TIMER ON/OFF pad and begin again.

15

Troubleshooting Tips Consumer Support

The timer is a minute timer only. The CLEAR/OFF pad does not affect the timer.

Touch the + or – pads until the amount of time you want shows in the display. The maximum time that can be entered in minutes is 59. Times more than 59 minutes should be changed to hours and minutes.

Touch the START/ON pad. The time will start counting down, although the display does not change until one minute has passed.

Installation Instructions

To Set the Timer

Care and Cleaning

To Turn Off the Clock Display

Operating Instructions

Touch the CLOCK pad twice.

Touch the START/ON pad until the time of day shows in the display. This enters the time and starts the clock.

Safety Instructions

Using the clock and timer. (on some models)

Not all features are on all models.

To Reset the Timer If the display is still showing the time remaining, you may change it by touching the KITCHEN TIMER ON/OFF or TIMER ON/OFF pad, then touch the + or – pads until the time you want appears in the display.

Operating Instructions

Safety Instructions

Using the clock and timer. (on some models)

If the remaining time is not in the display (clock, delay start or cooking time are in the display), recall the remaining time by touching the KITCHEN TIMER ON/OFF or TIMER ON/OFF pad and then touching the + or – pads to enter the new time you want.

To Cancel the Timer Touch the KITCHEN TIMER ON/OFF or TIMER ON/OFF pad twice.

Care and Cleaning

End of Cycle Tones (on some models) Clear the tones by pressing the pad of the function you are using.

or

Installation Instructions

or

Power Outage

Consumer Support Troubleshooting Tips

If a flashing time is in the display, you have experienced a power failure. Reset the clock.

16

To reset the clock, touch the CLOCK pad twice. Enter the correct time of day by touching the + or – pads. Touch the START/ON pad.

www.AmericanaAppliances.com

Do not lock the oven door with the latch during timed cooking. The latch is used for self-cleaning only. NOTE: Foods that spoil easily—such as milk, eggs, fish, stuffings, poultry and pork—should not be allowed to sit for more than 1 hour before or after cooking. Room temperature promotes the growth of harmful bacteria. Be sure that the oven light is off because heat from the bulb will speed harmful bacteria growth.

How to Set an Immediate Start and Automatic Stop

Touch the BAKE pad. Touch the + or – pads to set the oven temperature. Touch the COOKING TIME pad.

Touch the + or – pads to set the baking time.

The display shows either the oven temperature that you set or the cooking time countdown. (The display starts with PRE if showing the oven temperature.) The oven will continue to cook for the programmed amount of time, then turn off automatically. Touch the CLEAR/OFF pad to clear the display if necessary. Remove the food from the oven. Remember, even though the oven shuts off automatically, foods continue cooking after controls are off.

The cooking time that you entered will be displayed. (If you select Cooking Time first and then adjust the Bake Temperature, the oven temperature will be displayed instead).

The oven will turn on at the time of day you set, cook for a specific length of time and then turn off automatically. Make sure the clock shows the correct time of day. Touch the BAKE pad.

Touch the COOKING TIME pad. Touch the + or – pads to set the desired length of cooking time. Touch the START TIME pad. Touch the + or – pads to set the time of day you want the oven to turn on and start cooking.

When the oven turns on at the time of day you have set, the display will show PRE until it reaches the selected temperature, then it will display the oven temperature. At the end of cooking time, the oven will turn off and the end of cycle tone will sound. Touch the CLEAR/OFF pad to clear the display if necessary. Remove the food from the oven. Remember, even though the oven shuts off automatically, foods continue cooking after controls are off.

Touch the START/ON pad. NOTE: An attention tone will sound if you are using timed baking and do not touch the START/ON pad.

17

Troubleshooting Tips Consumer Support

Touch the + or – pads to set the oven temperature.

NOTE: If you would like to check the times you have set, touch the START TIME pad to check the start time you have set or touch the COOKING TIME pad to check the length of cooking time you have set.

Installation Instructions

How to Set a Delayed Start and Automatic Stop

Care and Cleaning

NOTE: If your recipe requires preheating, you may need to add additional time to the length of the cooking time.

Touch the START/ON pad.

Operating Instructions

The oven will turn on immediately and cook for a selected length of time. At the end of the cooking time, the oven will turn off automatically.

Safety Instructions

Using the timed baking and roasting features. (on some models)

Safety Instructions

Your new touch pad control has additional features that you may choose to use. The following are the features and how you may activate them. The special feature modes can only be activated while the display is showing the time of day. They remain in the control’s memory until the steps are repeated. When the display shows your choice, touch the START/ON pad. The special features will remain in memory after a power failure. NOTE: The Sabbath feature and the Thermostat Adjustment feature are also Special Features, but they are addressed separately in the following sections.

12 Hour Shut-Off

Care and Cleaning

Operating Instructions

Special features of your oven control. (on some models)

Touch the CLOCK pad. The display will show ON (12 hour shut-off). Touch the CLOCK pad repeatedly until the display shows OFF (no shut-off).

If you wish to turn OFF this feature, follow the steps below.

Touch the START/ON pad to activate the no shut-off and leave the control set in this special features mode.

Touch the BAKE and BROIL HI/LO pads at the same time for 3 seconds until the display shows SF.

Installation Instructions Consumer Support Troubleshooting Tips

With this feature, should you forget and leave the oven on, the control will automatically turn off the oven after 12 hours during baking functions or after 3 hours during a broil function.

18

(Designed for use on the Jewish Sabbath and Holidays)

www.AmericanaAppliances.com

The Sabbath feature can be used for baking/roasting only. It cannot be used for broiling, self-cleaning or Delay Start cooking. NOTE: The oven light comes on automatically (on some models) when the door is opened and goes off when the door is closed. The bulb may be removed. See the Oven Light Replacement section. On models with a light switch on the control panel, the oven light may be turned on and left on.

Safety Instructions

Using the Sabbath Feature. (on some models)

How to Set for Regular Baking/Roasting

Make sure the clock shows the correct time of day and the oven is off. Touch and hold both the BAKE and BROIL HI/LO pads, at the same time, until the display shows SF. Tap the CLOCK pad until SAb appears in the display.

Touch the BAKE pad. No signal will be given.

After a random delay period of approximately 30 seconds to 1 minute, ⊃ ⊃ will appear in the display indicating that the oven is baking/roasting. If ⊃ ⊃ doesn’t appear in the display, start again at Step 4. To adjust the oven temperature, touch the BAKE pad and tap the + or – pads to increase or decrease the temperature in 25° increments. Touch the START/ON pad. NOTE: The CLEAR/OFF and COOKING TIME pads are active during the Sabbath feature.

The preset starting temperature will automatically be set to 350.° Tap the + or – pads to increase or decrease the temperature in 25° increments. The temperature can be set between 170° and 550.° No signal or temperature will be given.

How to Set for Timed Baking/Roasting—Immediate Start and Automatic Stop NOTE: To understand how the oven control works, practice using regular (non-Sabbath) Immediate Start and Automatic Stop before entering the Sabbath mode.

Touch and hold both the BAKE and BROIL HI/LO pads, at the same time, until the display shows SF. Tap the CLOCK pad until SAb appears in the display. Touch the START/ON pad and ⊃ will appear in the display. Touch the COOKING TIME pad.

When the display shows ⊃ the oven is set in Sabbath. When the display shows ⊃ ⊃ the oven is baking/roasting.

Touch the START/ON pad. After a random delay period of approximately 30 seconds to 1 minute, ⊃ ⊃ will appear in the display indicating that the oven is baking/roasting. If ⊃ ⊃ doesn’t appear in the display, start again at Step 7.

Touch the + or – pads to set the desired length of cooking time between 1 minute and 9 hours and 59 minutes. The cooking time that you entered will be displayed.

To adjust the oven temperature, touch the BAKE pad and tap the + or – pads to increase or decrease the temperature in 25° increments. Touch the START/ON pad.

Touch the START/ON pad.

When cooking is finished, the display will change from ⊃ ⊃ to ⊃, indicating that the oven has turned OFF but is still set in Sabbath. Remove the cooked food.

Touch the BAKE pad. No signal will be given.

19

Troubleshooting Tips Consumer Support

Make sure the clock shows the correct time of day and the oven is off.

The preset starting temperature will automatically be set to 350.° Tap the + or – pads to increase or decrease the temperature in 25° increments. The temperature can be set between 170° and 550.° No signal or temperature will be given.

Installation Instructions

When the display shows ⊃ the oven is set in Sabbath. When the display shows ⊃ ⊃ the oven is baking/roasting.

Care and Cleaning

Touch the START/ON pad and ⊃ will appear in the display.

Touch the START/ON pad.

Operating Instructions

NOTE: To understand how the oven control works, practice using regular baking (non-Sabbath) before entering Sabbath mode.

Safety Instructions

Using the Sabbath Feature. (on some models) (Designed for use on the Jewish Sabbath and Holidays) How to Exit the Sabbath Feature Touch the CLEAR/OFF pad. If the oven is cooking, wait for a random delay period of approximately 30 seconds to 1 minute, until only ⊃ is in the display.

Operating Instructions

Touch and hold both the BAKE and BROIL HI/LO pads, at the same time, until the display shows SF.

Touch the START/ON pad.

Care and Cleaning

NOTE: If a power outage occurred while the oven was in Sabbath, the oven will automatically turn off and stay off even when the power returns. The oven control must be reset.

Installation Instructions Consumer Support Troubleshooting Tips

Tap the CLOCK pad until ON or OFF appears in the display. ON indicates that the oven will automatically turn off after 12 hours. OFF indicates that the oven will not automatically turn off. See the Special Features section for an explanation of the 12 Hour Shut-Off feature.

20

www.AmericanaAppliances.com

You may find that your new oven cooks differently than the one it replaced. Use your new oven for a few weeks to become more familiar with it. If you still think your new oven is too hot or too cold, you can adjust the thermostat yourself. Do not use thermometers, such as those found in grocery stores, to check the temperature setting of your oven. These thermometers may vary 20–40°F. NOTE: This adjustment will not affect the broiling or the self-cleaning temperatures (on some models). The adjustment will be retained in memory after a power failure.

Safety Instructions

Adjust the oven thermostat—Easy to do yourself!

To Adjust the Thermostat with this Type of Knob

Front of OVEN TEMP knob (knob appearance may vary)

Loosen both screws on the back of the knob. To increase the oven temperature, move the pointer toward the words “MAKE HOTTER.”

Care and Cleaning

Pointer

Replace the knob, matching the flat area of the knob to the shaft.

Operating Instructions

Tighten the screws.

Pull the Oven Temp knob off the shaft, look at the back of the knob and note the current setting before making any adjustments.

To decrease the oven temperature, turn the pointer toward the words “MAKE COOLER.” Each notch changes the temperature by 10°F. Back of OVEN TEMP knob

To Adjust the Thermostat on Other Models

Touch the BAKE pad. A two digit number shows in the display.

NOTE: This adjustment will not affect the broiling or self-cleaning temperatures. It will be retained in memory after a power failure.

Touch the – pad to decrease the temperature in 1 degree increments.

The type of margarine will affect baking performance! Most recipes for baking have been developed using high fat products such as butter or margarine (80% fat). If you decrease the fat, the recipe may not give the same results as with a higher fat product. Recipe failure can result if cakes, pies, pastries, cookies or candies are made with low fat spreads. The lower the fat content of a spread product, the more noticeable these differences become.

Federal standards require products labeled “margarine” to contain at least 80% fat by weight. Low-fat spreads, on the other hand, contain less fat and more water. The high moisture content of these spreads affects the texture and flavor of baked goods. For best results with your old favorite recipes, use margarine, butter or stick spreads containing at least 70% vegetable oil.

21

Troubleshooting Tips Consumer Support

The oven temperature can be adjusted up to (+) 35°F hotter or (–) 35°F cooler. Touch the + pad to increase the temperature in 1 degree increments.

When you have made the adjustment, touch the START/ON pad to go back to the time of day display. Use your oven as you would normally.

Installation Instructions

Touch the BAKE and BROIL HI/LO pads at the same time for 2 seconds until the display shows SF.

Safety Instructions

Never force the latch handle. Forcing the handle will damage the door lock mechanism. The oven door must be closed and all controls set correctly for the cycle to work properly.

Before a Clean Cycle For the first self-clean cycle, we recommend venting your kitchen with an open window or using a ventilation fan or hood. Remove the shelves, broiler pan, broiler grid, all cookware and any aluminum foil from the oven.

Wipe up heavy soil on the oven bottom.

Care and Cleaning

Operating Instructions

Using the self-cleaning oven. (on some models)

Do not use commercial oven cleaners or oven protectors in or near the self-cleaning oven. A combination of any of these products plus the high clean cycle temperatures may damage the porcelain finish of the oven. Soil on the front frame of the range and outside the gasket on the door will need to be cleaned by hand. Clean these areas with hot water, soap-filled steel-wool pads or cleansers such as Soft Scrub®. Rinse well with clean water and dry.

Wipe up any heavy spillovers on the oven bottom. Make sure the oven light bulb cover is in place and the oven light is off.

CAUTION:

The grates and drip pans (if so equipped) should never be cleaned in the self-cleaning oven. Do not use commercial oven cleaners or oven protectors in or near the self-cleaning oven. A combination of any of these products plus the high clean cycle temperatures may damage the porcelain finish of the oven. IMPORTANT: The health of some birds is extremely sensitive to the fumes given off during the self-cleaning cycle of any range. Move birds to another well ventilated room.

How to Set the Oven for Cleaning

Installation Instructions Consumer Support Troubleshooting Tips

The oven shelves can be self-cleaned, but they will darken, lose their luster and become hard to slide.

Do not clean the gasket. The fiberglass material of the oven door gasket cannot withstand abrasion. It is essential for the gasket to remain intact. If you notice it becoming worn or frayed, replace it.

Follow the directions in the Before a Clean Cycle section. Latch the door. NOTE: Never force the latch. If the oven is too hot, you will not be able to slide the latch. Allow the oven to cool. Touch the SELF CLEAN pad. Touch the + or – pads until the desired Clean Time is displayed. The Clean Time is normally 4 hours and 20 minutes. You can change the Clean Time to any time between 3 and 5 hours, depending on the amount of soil in your oven. Touch the START/ON pad.

22

The self-clean cycle will automatically begin after CLEAN is displayed and the time countdown appears in the display. While the oven is self-cleaning, you can touch the CLOCK pad to display the time of day. To return to the clean countdown, touch the SELF CLEAN pad. The oven shuts off automatically when the clean cycle is complete, and 0:00 will flash in the display. Slide the latch handle to the left as far as it will go and open the door.

The oven door must be closed and all controls set correctly for the cycle to work properly.

How to Delay the Start of Cleaning Change the Start Time by touching the + or – pads. The start time will appear in the display.

Make sure the clock shows the correct time of day.

The self-clean cycle will automatically begin at the time set.

Follow the directions in the Before a Clean Cycle section.

While the oven is self-cleaning, you can touch the CLOCK pad to display the time of day. To return to the clean countdown, touch the SELF CLEAN pad.

Latch the door. NOTE: Never force the latch. If the oven is too hot, you will not be able to slide the latch. Allow the oven to cool. Touch the SELF CLEAN pad.

The oven shuts off automatically when the clean cycle is complete, and 0:00 will flash in the display. Slide the latch handle to the left as far as it will go and open the door.

Touch the START TIME pad.

Installation Instructions

To Stop a Clean Cycle Touch the CLEAR/OFF pad. Wait until the oven has cooled below the locking temperature to unlatch the door. You will not be able to open the door right away unless the oven has cooled below the locking temperature.

You cannot set the oven for cooking until the oven is cool enough for the door to be unlatched.

■ You cannot set the oven for cooking until the oven is cool enough for the door to unlock.

You may notice some white ash in the oven. Wipe it up with a damp cloth after the oven cools.

■ While the oven is self-cleaning, you can touch the CLOCK pad to display the time of day. To return to the clean countdown, touch the COOKING TIME pad.

These deposits are usually a salt residue that cannot be removed by the clean cycle.

■ If the shelves become hard to slide, apply a small amount of vegetable oil or cooking oil to a paper towel and wipe the edges of the oven shelves with the paper towel.

If the oven is not clean after one clean cycle, repeat the cycle.

23

Troubleshooting Tips Consumer Support

After a Clean Cycle

If white spots remain, remove them with a soapfilled steel-wool pad and rinse thoroughly with a vinegar and water mixture.

Care and Cleaning

Touch the + or – pads to set the Clean Time. The Clean Time is preset for 4 hours and 20 minutes. You can change the Clean Time to any time between 3 and 5 hours, depending on the amount of soil in your oven. If a different Clean Time is desired, touch the + or – pads until the desired Clean Time is displayed.

Touch the START/ON pad.

Operating Instructions

You can set the oven control to delay-start the oven, clean for a specific length of time and then turn off automatically.

Safety Instructions

www.AmericanaAppliances.com

Safety Instructions

Care and cleaning of the range. Be sure electrical power is off and all surfaces are cool before cleaning any part of the range. If your range is removed for cleaning, servicing or any reason, be sure the anti-tip device is re-engaged properly

when the range is replaced. Failure to take this precaution could result in tipping of the range and cause injury.

Oven Interior (non-self clean models)

Operating Instructions

With proper care, the porcelain enamel finish on the inside of the oven---top, bottom, sides, back and inside of the door--will stay new-looking for years. Let the range cool before cleaning. We recommend that you wear rubber gloves when cleaning the range.

Consumer Support Troubleshooting Tips

Installation Instructions

Care and Cleaning

Soap and water will normally do the job. Heavy spattering or spillovers may require cleaning with a mild abrasive cleaner. Soap-filled scouring pads may also be used. Do not allow food spills with a high sugar or acid content (such as milk, tomatoes, sauerkraut, fruit juices or pie filling) to remain on the surface. They may cause a dull spot even after cleaning. Household ammonia may make the cleaning job easier. Place 1/2 cup in a shallow glass or pottery container in a cold

oven overnight. The ammonia fumes will help loosen the burned-on grease and food. If necessary, you may use an oven cleaner. Follow the package directions. Do not spray oven cleaner on the electrical controls and switches because it could cause a short circuit and result in sparking or fire. Do not allow a film from the cleaner to build up on the temperature sensor–it could cause the oven to heat improperly. (The sensor is located at the top of the oven.) Carefully wipe the sensor clean after each oven cleaning, being careful not to move the sensor as a change in its position could affect how the oven bakes. Do not spray any oven cleaner on the oven door, handles or any exterior surface of the oven, cabinets or painted surfaces. The cleaner can damage these surfaces.

Lift-Off Oven Door

Lift the door straight up and off the hinges.

The oven door is removable for cleaning.

To clean the outside of the door:

Do not lift the door by the handle. Make sure the oven is completely cool.

■ Use soap and water to thoroughly clean the top, sides and front of the oven door. Rinse well. You may also use a glass cleaner to clean the glass on the outside of the door. Do not let water drip into the vent openings.

To remove the door, open it to the special stop position. Grasp firmly on each side and lift the door straight up and off the hinges. Do not place hands between the hinge and the oven door frame.

The gasket is designed with a gap at the bottom to allow for proper air circulation. Because the area inside the gasket is cleaned during the self-clean cycle, you do not need to clean this by hand on self-clean models. The area outside the gasket and the front frame can be cleaned with a soap-filled steel-wool pad, hot water and detergent. Rinse well with a vinegar and water solution. Do not rub or clean the door gasket–it has an extremely low resistance to abrasion. If you notice the gasket becoming worn, frayed or damaged in any way, or if it has become displaced on the door, you should have it replaced.

24

To replace the door, make sure the hinges are in the special stop position. Position the slots in the bottom of the door squarely over the hinges and slowly lower it over both hinges. To clean the inside of the door: ■ Do not allow excess water to run into any holes or slots in the door. ■ Soap and water will normally do the job. Heavy spattering or spillovers may require cleaning with a mild abrasive cleaner. Soap-filled, steel-wool pads may also be used. Do not allow food spills with a high sugar or acid content (such as milk, tomatoes, sauerkraut, fruit juices or pie filling) to remain on the surface. They may cause a dull spot even after cleaning.

■ Spillage of marinades, fruit juices, tomato sauces and basting materials containing acids may cause discoloration and should be wiped up immediately. When surface is cool, clean and rinse. ■ Do not use oven cleaners, cleaning powders or harsh abrasives on the outside of the door.

Oven Heating Elements Do not clean the bake element or the broil element. Any soil will burn off when the elements are heated. To clean the oven floor, gently lift the bake element. Clean with warm soapy water.

Clean the oven shelves with an abrasive cleanser or scouring pad. After cleaning, rinse the shelves with clean water and dry with a clean cloth.

To make the shelves slide more easily, apply a small amount of vegetable oil or cooking oil to a paper towel and wipe the edges of the oven shelves with the paper towel.

NOTE: Take the shelves out of the oven before you begin the self-clean cycle or they may discolor.

Care and Cleaning

Oven Light Replacement (on some models) CAUTION: Before replacing your oven light bulb, turn the oven light off and disconnect the electrical power to the range at the main fuse or circuit breaker panel.

Wire cover holder

Be sure to let the light cover and bulb cool completely.

Operating Instructions

Oven Shelves

Safety Instructions

www.AmericanaAppliances.com

To replace the cover: Place it into groove of the light receptacle. Pull wire forward to the center of the cover until it snaps into place. Connect electrical power to the range.

To remove the cover:

Installation Instructions

Hold a hand under the cover so it doesn’t fall when released. With fingers of the same hand, firmly push back the wire cover holder. Lift off the cover. Do not remove any screws to remove the cover. Replace bulb with a 40-watt household appliance bulb.

Troubleshooting Tips Consumer Support

25

Broiler Pan & Grid After broiling, remove the broiler pan from the oven.

Consumer Support Troubleshooting Tips

Installation Instructions

Care and Cleaning

Operating Instructions

Safety Instructions

Care and cleaning of the range. Do not clean the broiler pan or grid in a self-cleaning oven. After broiling, remove the broiler pan from the oven. Remove the grid from the pan. Carefully pour out the grease from the pan into a proper container.

The broiler pan may be cleaned with a commercial oven cleaner. If the grid is grey enamel, it can also be cleaned with an oven cleaner. Both the broiler pan and grid can also be cleaned in the dishwasher.

Wash and rinse the broiler pan and grid in hot water with a soap-filled or plastic scouring pad.

Do not store a soiled broiler pan and grid anywhere in the range.

If food has burned on, sprinkle the grid with detergent while hot and cover with wet paper towels or a dishcloth. Soaking the pan will remove burned-on foods.

Do not clean the broiler pan or grid in a self-cleaning oven.

CAUTION:

Storage Drawer Removal To remove the storage drawer:

To replace the storage drawer:

Pull the drawer out all the way.

Insert glides at the back of the drawer beyond the stop on range glides.

Tilt up the front and remove it.

Lift the drawer if necessary to insert easily.

Clean under the range.

Let the front of the drawer down, then push in to close.

Control Panel and Knobs

Pull the knob straight off the stem.

It’s a good idea to wipe the control panel after each use of the oven. Use a damp cloth to clean or rinse. For cleaning, use mild soap and water or a 50/50 solution of vinegar and water. For rinsing, use clean water. Polish dry with a soft cloth. Do not use abrasive cleansers, strong liquid cleaners, plastic scouring pads or oven cleaners on the control panel—they will damage the finish. The control knobs may be removed for easier cleaning. Make sure the knobs are in the OFF positions and pull them straight off the stems for cleaning.

26

The knobs can be cleaned in a dishwasher or they may also be washed with soap and water. Make sure the insides of the knobs are dry before replacing. Replace the knobs in the OFF position to ensure proper placement.

Porcelain Enamel Cooktop (on some models) The porcelain enamel finish is sturdy but breakable if misused. This finish is acid-resistant. However, any acidic foods spilled (such as fruit juices, tomato or vinegar) should not be permitted to remain on the finish.

If acids spill on the cooktop while it is hot, use a dry paper towel or cloth to wipe it up right away. When the surface has cooled, wash with soap and water. Rinse well.

Lift-Up Cooktop (on some models) After cleaning under the cooktop with hot, mild soapy water and a clean cloth, lower the cooktop. Be careful not to pinch your fingers.

The surface units do not need to be removed; however, you may remove one to make raising the cooktop easier. There are two side supports that lock into position when the cooktop is lifted up.

To lower the cooktop, push the rods back and gently lower the cooktop until it rests in place.

Surface Units (on some models)

Surface unit

Drip pan

To clean the surface units, turn the control to the highest setting for a minute. The coils will burn off any soil.

Do not lift the surface unit more than 1″. If you do, it may not lie flat on the drip pan when you plug it back in. Repeated lifting of the surface unit more than 1 inch above the drip pan can permanently damage the receptacle.

Do not immerse the surface units in liquids of any kind. Do not clean the surface units in a dishwasher. Do not bend the surface unit plug terminals. Do not attempt to clean, adjust or in any way repair the plug-in receptacle.

Drip Pans (if so equipped) Remove the surface units. Then lift out the drip pans.

Clean the area under the drip pans often. Built-up soil, especially grease, may catch fire.

Place them in a covered container. Add 1/4 cup ammonia and let soak several hours or overnight. Wash, rinse well and dry.

Do not cover the drip pans with foil. Using foil so close to the receptacle could cause shock, fire or damage to the range.

The drip pans may also be cleaned in the dishwasher.

NOTE: Do not clean the drip pans in a self-cleaning oven.

27

Troubleshooting Tips Consumer Support

To remove a surface unit: To remove the drip pans for cleaning, the surface units must be removed first. Lift the surface unit about 1 inch above the drip pan and pull it out.

To replace a surface unit: Replace the drip pan into the recess in the cooktop. Make sure the opening in the pan lines up with the receptacle. Insert the terminals of the surface unit through the opening in the drip pan and into the receptacle. Guide the surface unit into place so it rests evenly.

Installation Instructions

Be sure all the controls are turned to OFF and the surface units are cool before attempting to remove them. Receptacle

NOTE: Do not lift the cooktop on radiant top models. Lifting the cooktop can lead to damage and improper operation of the range.

Care and Cleaning

Be sure all surface units are turned off before raising the cooktop.

Some models have a cooktop that can be lifted up for easier cleaning. The entire cooktop may be lifted up and supported in the up position.

Operating Instructions

For other spills such as fat spatterings, wash with soap and water or cleansing powders after the surface has cooled. Rinse well. Polish with a dry cloth.

Safety Instructions

www.AmericanaAppliances.com

Oven Vent On glass cooktop models, the oven is vented through an opening at the rear of the cooktop.

Painted Surfaces (on some models) Painted surfaces include the sides of the range and the sides of the door trim.

Care and Cleaning

To clean the painted surfaces, use a hot, damp cloth with a mild detergent suitable for these surfaces. Use a clean, hot, damp cloth to remove soap. Dry with a dry, clean cloth.

Do not use steel-wood pads, commercial oven cleaners, cleaning powders or other abrasive cleaners. They will damage the surface.

Stainless Steel Surfaces (on some models) Do not use a steel-wool pad; it will scratch the surface. To clean the stainless steel surface, use warm sudsy water or a stainless steel cleaner or polish. Always wipe the surface in the direction of the grain. Follow the cleaner instructions for cleaning the stainless steel surface.

Installation Instructions Consumer Support Troubleshooting Tips

Never cover the opening with aluminum foil or any other material.

On coil cooktop models, the oven is vented through an opening under the right rear surface unit.

Operating Instructions

Safety Instructions

Care and cleaning of the range.

Glass Window (on some models) To clean the outside glass finish, use a glass cleaner. Rinse and polish with a dry cloth.

28

To inquire about purchasing stainless steel appliance cleaner or polish, or to find the location of a dealer nearest you, please call our toll-free number: National Parts Center 800.626.2002 ge.com

www.AmericanaAppliances.com

Normal Daily Use Cleaning ONLY use CERAMA BRYTE® Ceramic Cooktop Cleaner on the glass cooktop. Other creams may not be as effective. To maintain and protect the surface of your glass cooktop, follow these steps:

Daily use of CERAMA BRYTE® Ceramic Cooktop Cleaner will help keep the cooktop looking new.

Use a paper towel or CERAMA BRYTE® Cleaning Pad for Ceramic Cooktops to clean the entire cooktop surface. Use a dry cloth or paper towel to remove all cleaning residue. No need to rinse. NOTE: It is very important that you DO NOT heat the cooktop until it has been cleaned thoroughly.

WARNING: DAMAGE to your glass surface may occur if you use scrub pads other than those recommended. Allow the cooktop to cool.

Use a CERAMA BRYTE® Cleaning Pad for Ceramic Cooktops.

Spread a few drops of CERAMA BRYTE® Ceramic Cooktop Cleaner on the entire burned residue area.

If any residue remains, repeat the steps listed above as needed. For additional protection, after all residue has been removed, polish the entire surface with CERAMA BRYTE® Ceramic Cooktop Cleaner and a paper towel.

Heavy, Burned-On Residue Allow the cooktop to cool.

After scraping with the razor scraper, spread a few drops of CERAMA BRYTE® Ceramic Cooktop Cleaner on the entire burned residue area. Use the CERAMA BRYTE® Cleaning Pad to remove any remaining residue.

29

Troubleshooting Tips Consumer Support

The CERAMA BRYTE® Ceramic Cooktop Scraper and all recommended supplies are available through our Parts Center. See instructions under “To Order Parts” section on next page. NOTE: Do not use a dull or nicked blade.

Use a single-edge razor blade scraper at approximately a 45° angle against the glass surface and scrape the soil. It will be necessary to apply pressure to the razor scraper in order to remove the residue.

For additional protection, after all residue has been removed, polish the entire surface with CERAMA BRYTE® Ceramic Cooktop Cleaner and a paper towel.

Installation Instructions

Using the included CERAMA BRYTE® Cleaning Pad for Ceramic Cooktops, rub the residue area, applying pressure as needed.

Care and Cleaning

Burned-On Residue

Operating Instructions

Clean your cooktop after each spill. Use CERAMA BRYTE® Ceramic Cooktop Cleaner.

Before using the cooktop for the first time, clean it with CERAMA BRYTE® Ceramic Cooktop Cleaner. This helps protect the top and makes cleanup easier.

Shake the cleaning cream well. Apply a few drops of CERAMA BRYTE® Ceramic Cooktop Cleaner directly to the cooktop.

Safety Instructions

Cleaning the glass cooktop. (on some models)

Metal Marks and Scratches Be careful not to slide pots and pans across your cooktop. It will leave metal markings on the cooktop surface. These marks are removable using the CERAMA BRYTE® Ceramic Cooktop Cleaner with the CERAMA BRYTE® Cleaning Pad for Ceramic Cooktops.

Consumer Support Troubleshooting Tips

Installation Instructions

Care and Cleaning

Operating Instructions

Safety Instructions

Cleaning the glass cooktop. (on some models) If pots with a thin overlay of aluminum or copper are allowed to boil dry, the overlay may leave black discoloration on the cooktop. This should be removed immediately before heating again or the discoloration may be permanent. WARNING: Carefully check the bottom of pans for roughness that would scratch the cooktop.

Cooktop Seal To clean the cooktop seal around the edges of the glass, lay a wet cloth on it

for a few minutes, then wipe clean with nonabrasive cleaners.

Glass surface—potential for permanent damage. Our testing shows that if you are cooking high sugar mixtures such as jelly or fudge and have a spillover, it can cause permanent damage to the glass surface unless the spillover is immediately removed.

Damage from Sugary Spills and Melted Plastic Turn off all surface units. Remove hot pans. Wearing an oven mitt: a. Use a single-edge razor blade scraper (CERAMA BRYTE® Ceramic Cooktop Scraper) to move the spill to a cool area on the cooktop. b. Remove the spill with paper towels.

To Order Parts To order CERAMA BRYTE® Ceramic Cooktop Cleaner and the cooktop scraper, please call our toll-free number: National Parts Center . . . . . 800.626.2002 CERAMA BRYTE ® Ceramic Cooktop Cleaner . . . . . . . . . .# WX10X300 CERAMA BRYTE® Ceramic Cooktop Scraper . . . . . . . . .# WX10X0302 Kit . . . . . . . . . . . . . . . . . . . . . .# WB64X5027 (Kit includes cream and cooktop scraper) CERAMA BRYTE® Cleaning Pads for Ceramic Cooktops . . . . . . . .# WX10X350

30

Any remaining spillover should be left until the surface of the cooktop has cooled. Don’t use the surface units again until all of the residue has been completely removed. NOTE: If pitting or indentation in the glass surface has already occurred, the cooktop glass will have to be replaced. In this case, service will be necessary.

Installation Instructions

Free-Standing Electric Ranges

Questions? Call 1.800.432.2737

BEFORE YOU BEGIN

FOR YOUR SAFETY:

Read these instructions completely and carefully.

All rough-in and spacing dimensions must be met for safe use of your range. Electricity to the range can be disconnected at the outlet without moving the range if the outlet is in the preferred location (remove lower drawer).



IMPORTANT



IMPORTANT

• • • • • •

— Save these instructions for local inspector’s use. — Observe all governing codes and ordinances. Note to Installer – Be sure to leave these instructions with the Consumer. Note to Consumer – Keep these instructions for future reference. Skill level – Installation of this appliance requires basic mechanical skills. Completion time – 1 to 3 hours Proper installation is the responsibility of the installer. Product failure due to improper installation is not covered under the Warranty.

To reduce the risk of burns or fire when reaching over hot surface elements, cabinet storage space above the cooktop should be avoided. If cabinet storage space is to be provided above the cooktop, the risk can be reduced by installing a range hood that sticks out at least 5” beyond the front of the cabinets. Cabinets installed above a cooktop must be no deeper than 13” . Be sure your appliance is properly installed and grounded by a qualified technician. Make sure the cabinets and wall coverings around the range can withstand the temperatures (up to 200°F.) generated by the range.

WARNING

— This appliance must be properly grounded.

ANTI-TIP DEVICE

WARNING

— To reduce the risk of tipping, the appliance must be secured by properly installed Anti-Tip bracket packed with this appliance. If the Anti-Tip device supplied with the range does not fit this application, use the universal Anti-Tip device WB2X7909.

FOR YOUR SAFETY:

WARNING

— Before beginning the installation, switch power off at service panel and lock the service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.

WARNING — • All ranges can tip • Injury to persons could result • Install Anti-Tip bracket packed with range • See Installation Instructions If you pull the range out and away from the wall for any reason, make sure the Anti-Tip bracket is engaged when the range is pushed back against the wall.

31

Installation Instructions PREPARE TO INSTALL THE RANGE MATERIALS YOU MAY NEED

Tin Snips

Lag Bolts

2 PREPARE THE OPENING Allow 11⁄2″ spacing from the range to adjacent vertical walls above the cooktop surface. Allow 30″ minimum clearance between the surface units and the bottom of unprotected wood or metal top cabinet, and 15″ minimum between the countertop and adjacent cabinet bottom. EXCEPTION: Installation of a listed microwave oven or cooking appliance over the cooktop shall conform to the installation instructions packed with that appliance. If cabinet storage is installed, reduce the risk by installing a range hood that projects horizontally a min. of 5″ beyond the bottom of the cabinets. Make sure the wall covering, countertops and cabinets around the range can withstand heat generated by the range, oven or cooktop up to 200°F.

Anchor Sleeves

(For Anti-Tip Bracket Mounted on Concrete Floors Only)

(UL Approved 40 AMP) 4-Wire Cord OR 3-Wire Cord 4‘ Long 4‘ Long

Squeeze Connector (For Conduit Installations Only)

TOOLS YOU WILL NEED

Drill with 1/8” Bit

Safety Glasses Hood 5″ Min.

Not less than the width of the range

Adjustable Wrench 30″ 15″ Min. Min.

Tape Measure

Pliers

Locate the outlet box within either shaded area.

Pencil

Wall 11⁄2″ Min.

1/4” Nut Driver

Phillips Screwdriver

Level

71⁄2″

Wall

Install the outlet box on either side of the CL

Flat-blade Screwdriver

PARTS INCLUDED

Anti-Tip Bracket Kit

1 REMOVE SHIPPING MATERIALS Remove packaging materials. Failure to remove packaging materials could result in damage to the appliance.

32

C L of range 7″

Outlet box

71⁄2″

31⁄2″

5″ Floor

21⁄4″

Cord

Flooring under the range Your range, like many other household items, is heavy and can settle into soft floor coverings such as cushioned vinyl or carpeting. When moving the range on this type of flooring, it should be installed on a 1/4″ thick sheet of plywood (or similar material) as follows: When the floor covering ends at the front of the range, the area that the range will rest on should be built up with plywood to the same level or higher than the floor covering. This will allow the range to be moved for cleaning or servicing.

Installation Instructions ELECTRICAL CONNECTIONS ELECTRICAL REQUIREMENTS

ALL NEW CONSTRUCTIONS, MOBILE HOMES AND INSTALLATIONS WHERE LOCAL CODES DO NOT ALLOW GROUNDING THROUGH NEUTRAL

CAUTION:

For personal safety, do not use an extension cord with this appliance. Remove house fuse or open circuit breaker before beginning installation. This appliance must be supplied with the proper voltage and frequency, and connected to an individual properly grounded branch circuit, protected by a circuit breaker or fuse having amperage as specified on the rating plate. The rating plate is located behind the storage drawer on the oven frame.

Use only a 3-conductor or a 4-conductor UL-listed range cord. These cords may be provided with ring terminals on wire and a strain relief device. A range cord rated at 40 amps with 125/250 minimum volt range is required. A 50 amp range cord is not recommended but if used, it should be marked for use with nominal 13⁄8″ diameter connection openings. Care should be taken to center the cable and strain relief within the knockout hole to keep the edge from damaging the cable.

Location of model rating plate

We recommend you have the electrical wiring and hookup of your range connected by a qualified electrician. After installation, have the electrician show you where your main range disconnect is located.

• Because range terminals are not accessible after range is in position, flexible service conduit or cord must be used. NOTE: If conduit is being used, go to Step 3D and then to Step 6 or 7.

Check with your local utilities for electrical codes which apply in your area. Failure to wire your oven according to governing codes could result in a hazardous condition. If there are no local codes, your range must be wired and fused to meet the requirements of the National Electrical Code, ANSI/NFPA No. 70– Latest Edition. You can get a copy by writing:

• On some models, a filter capacitor may be connected between the black and white leads on the junction block.

National Fire Protection Association Batterymarch Park Quincy, MA 02269 Effective January 1, 1996, the National Electrical Code requires that new construction (not existing) utilize a 4-conductor connection to an electric range. When installing an electric range in new construction, follow Steps 3 and 5 for 4-wire connection. You must use a 3-wire, single-phase A.C. 208Y/120 Volt or 240/120 Volt, 60 hertz electrical system. If you connect to aluminum wiring, properly installed connectors approved for use with aluminum wiring must be used. If the electrical service provided does not meet the above specifications, have a licensed electrician install an approved outlet.

33

Installation Instructions ELECTRICAL CONNECTIONS 3 POWER CORD AND STRAIN RELIEF INSTALLATION A

(CONT.) C

Remove the wire cover (on the lower back of the range) by removing two (2) screws using a 1/4” nut driver. Do not discard these screws.

2 screws to remove wire cover

For power cord installations only (see the next step if using conduit), assemble the strain relief in the hole. Insert the power cord through the strain relief and tighten. Allow enough slack to easily attach the cord terminals to the terminal block. If tabs are present at the end of the winged strain relief, they can be removed for better fit. NOTE: Do not install the power cord without a strain relief. The strain relief bracket should be installed before reinstalling the rear range wiring cover. Terminal block

Retaining tab

Strain relief

Back of range Wire cover

B

Power cord

Remove the knockout ring (13⁄8″) located on bracket directly below the terminal block. To remove the knockout, use a pair of pliers to bend the knockout ring away from the bracket and twist until ring is removed.

Bracket

Skip to Step 4 or 5.

D

Terminal block (appearance may vary)

For conduit installations only, purchase a squeeze connector matching the diameter of your conduit and assemble it in the hole. Insert the conduit through the squeeze connector and tighten. Allow enough slack to easily attach the wires to the terminal block. NOTE: Do not install the conduit without a squeeze connector. The squeeze connector should be installed before reinstalling the rear range wiring cover.

Terminal block Knockout ring in bracket

Knockout ring removed Squeeze connector Conduit

Skip to Step 6 or 7.

34

Bracket

Installation Instructions 4 3-WIRE POWER CORD INSTALLATION

5 4-WIRE POWER CORD INSTALLATION

WARNING:

WARNING:

The neutral or ground wire of the power cord must be connected to the neutral terminal located in the center of the terminal block. The power leads must be connected to the lower left and the lower right terminals of the terminal block.

A

The neutral wire of the supply circuit must be connected to the neutral terminal located in the lower center of the terminal block. The power leads must be connected to the lower left and the lower right terminals of the terminal block. The 4th grounding lead must be connected to the frame of the range with the ground plate and the ground screw.

Remove the 3 lower terminal screws from the terminal block. Insert the 3 terminal screws through each power cord terminal ring and into the lower terminals of the terminal block. Be certain that the center wire (white/neutral) is connected to the center lower position of the terminal block. Tighten screws securely into the terminal block. DO NOT remove the ground strap connection.

A

B C

D

Terminal block (appearance may vary) Neutral terminal

Remove the 3 lower terminal screws from the terminal block. Remove the ground screw and ground plate and retain them. Cut and discard the ground strap. DO NOT DISCARD ANY SCREWS. Insert the one ground screw into the power cord ground wire terminal ring, through the ground plate and into the frame of the range. Insert the 3 terminal screws (removed earlier) through each power cord terminal ring and into the lower terminals of the terminal block. Be certain that the center wire (white/neutral) is connected to the center lower position of the terminal block. Tighten screws securely into the terminal block.

Before

Ground strap

Ground plate Ground strap

Ground strap

After Power cord Terminal block

B

or

Terminal block

Skip to Step 8 and proceed with the installation.

Neutral terminal Neutral terminal Ground plate (grounding to range)

Ground screw

E

35

Skip to Step 8 and proceed with the installation.

Installation Instructions ELECTRICAL CONNECTIONS 6 3-WIRE CONDUIT INSTALLATION A

(CONT.) 7 4-WIRE CONDUIT INSTALLATION

Loosen the 3 lower terminal screws from the terminal block. Insert the center bare wire (white/neutral) tip through the bottom center terminal block opening. On certain models, the wire will need to be inserted through the ground strap opening and then into the bottom center block opening. Insert the two side bare wire tips into the lower left and the lower right terminal block openings. Tighten the screws until the wire is firmly secure (approximately 20 inch-lbs.).

A

B

NOTE: ALUMINUM WIRING: Aluminum building wire may be used but it must be rated for the correct amperage and voltage to make connection. Connect wires according to this Step 6 or Step 7 depending on number of wires.

Loosen the three lower terminal screws from the terminal block. Remove the ground screw and ground plate and retain them. Cut and discard the ground strap. DO NOT DISCARD ANY SCREWS. Insert the ground bare wire tip between the range frame and the ground plate (removed earlier) and secure it in place with the ground screw (removed earlier). Insert the bare wire (white/neutral) tip through the bottom center of the terminal block opening. Insert the two side bare wire tips into the lower left and the lower right terminal block openings. Tighten the screws until the wire is firmly secure (approximately 20 inch-lbs.).

Before

Ground strap

Terminal block Terminal block

Ground strap

Wire tips

After Terminal block

Bracket

Wire tips

Conduit

Wire used, location and enclosure of splices, etc., must conform to good wiring practices and local codes. B

or

Neutral terminal

Ground plate (grounding to range)

Ground screw

Skip to Step 8 and proceed with the installation.

Bracket

Wire used, location and enclosure of splices, etc., must conform to good wiring practices and local codes. C

36

Proceed to Step 8.

Installation Instructions INSTALL THE RANGE 8 REPLACE THE WIRE COVER

10 LEVEL THE RANGE

Replace the wire cover on the range back by sliding its right edge under the retaining tab and replacing the two screws removed earlier. Make sure that no wires are pinched between the cover and the range back. 2 screws to replace wire cover

A B

Retaining tab

Wire cover

C

Back of range

Install the oven shelves in the oven and position the range where it will be installed. Check for levelness by placing a spirit level or a cup, partially filled with Spirit level water, on one of the oven shelves. If using a spirit level, take two readings—with the level placed diagonally first in one direction and then the other. Remove the storage drawer, broiler drawer or kick panel. The front leveling legs can be adjusted from the bottom and the rear legs can be adjusted from the top or the bottom. Lower range

9 ANTI-TIP DEVICE INSTALLATION

Leg leveler

An Anti-Tip bracket is supplied with instructions for installation in a variety of locations. The instructions include all necessary information to complete the installation. Read the Safety Instructions and the instructions that fit your situation before beginning installation. Bracket

Raise range Front leveling legs (on some models)

Raise range

Lower range

Wall plate

Screw must enter wood or metal

Typical installation of anti-tip bracket attachment to wall

WARNING:

Rear leveling legs (on some models)

• Range must be secured by Anti-Tip bracket supplied. D

• If the Anti-Tip device supplied with the range does not fit this application, use the universal Anti-Tip device WB2X7909.

E

• See instructions to install (supplied with bracket). • Unless properly installed, the range could be tipped by stepping or sitting on the door. Injury may result from spilled hot liquids or from the range itself.

37

Use an open-end or adjustable wrench to adjust the leveling legs until the range is level. Replace the drawer or panel.

Installation Instructions INSTALL THE RANGE

(CONT.)

11 FINAL INSTALLATION CHECKLIST

12 OPERATION CHECKLIST • Turn on one of the surface units to observe that the element glows within 60 seconds. Turn the unit off when glow is detected. If the glow is not detected within the time limit, recheck the range wiring connections. If change is required, retest again. If no change is required, have building wiring checked for proper connections and voltage.

• Check to make sure the circuit breaker is closed (RESET) or the circuit fuses are replaced. • Be sure power is in service to the building. • Note (on some models): If the clock flashes “bAd” and then “LinE” with a loud tone, the neutral connection to the range is miswired. Check the terminal block connections and/or house wiring to correct.

• Check to make sure the Clock (on models so equipped) display is energized. If a series of horizontal red lines appear in the display, disconnect power immediately. Recheck the range wiring connections. If change is made to connections, retest again. If no change is required, have building wiring checked for proper connections and voltage. It is recommended that the clock be changed if the red lines appear.

• Check to be sure that all packing materials and tape have been removed. This will include tape on metal panel under control knobs (if applicable), adhesive tape, wire ties, cardboard and protective plastic. Failure to remove these materials could result in damage to the appliance once the appliance has been turned on and surfaces have heated.

• Be sure all range controls are in the OFF position before leaving the range.

• Check to make sure that the rear leveling leg is fully inserted into the Anti-Tip bracket and that the bracket is securely installed.

38

www.AmericanaAppliances.com

Troubleshooting Tips Save time and money! Review the charts on the following pages first and you may not need to call for service.

Problem

Possible Causes

What To Do

Surface units will not maintain a rolling boil or cooking is not fast enough

Improper cookware being used.

•Use pans which are flat and match the diameter of the surface unit selected.

Surface units do not work properly

A fuse in your home may be blown or the circuit breaker tripped.

• Replace the fuse or reset the circuit breaker.

Cooktop controls improperly set.

• Check to see the correct control is set for the surface unit you are using.

Scratches (may appear as cracks) on cooktop glass surface

Incorrect cleaning methods being used. Cookware with rough bottoms being used or coarse particles (salt or sand) were between the cookware and the surface of the cooktop. Cookware has been slid across the cooktop surface.

• Scratches are not removable. Tiny scratches will become less visible in time as a result of cleaning. • To avoid scratches, use the recommended cleaning procedures. Make sure bottoms of cookware are clean before use, and use cookware with smooth bottoms.

Areas of discoloration on the cooktop

Food spillovers not cleaned before next use.

• See the Cleaning the glass cooktop section.

Hot surface on a model with a light-colored glass cooktop.

• This is normal. The surface may appear discolored when it is hot. This is temporary and will disappear as the glass cools.

Plastic melted to the surface

Hot cooktop came into contact with plastic placed on the hot cooktop.

• See the Glass surface—potential for permanent damage section in the Cleaning the glass cooktop section.

Pitting (or indentation) of the cooktop

Hot sugar mixture spilled on the cooktop.

• Call a qualified technician for replacement.

Frequent cycling off and on of surface units

Improper cookware being used.

• Use only flat cookware to minimize cycling.

Safety Instructions

Before you call for service…

Radiant Cooktops

Operating Instructions Care and Cleaning Installation Instructions Troubleshooting Tips Consumer Support

39

Safety Instructions

Before you call for service… Troubleshooting Tips

Problem

Possible Causes

What To Do

The surface units are not plugged in solidly.

•With the controls off, check to make sure the surface unit is plugged completely into the receptacle.

The surface unit controls improperly set.

•Check to see the correct control is set for the surface unit you are using.

Operating Instructions

Coil Cooktops Surface units not functioning properly

The drip pans are not set securely •With the controls off, check to make sure the drip pan is in the cooktop. in the recess in the cooktop and that the opening in the pan lines up with the receptacle.

Consumer Support Troubleshooting Tips

Installation Instructions

Care and Cleaning

Oven–All Models Oven light does not work

Light bulb is loose or defective.

•Tighten or replace the bulb.

Switch operating light is broken. •Call for service. Oven will not work

Food does not bake or roast properly

40

Plug on range is not completely inserted in the electrical outlet.

• Make sure electrical plug is plugged into a live, properly grounded outlet.

A fuse in your home may be blown or the circuit breaker tripped.

• Replace fuse or reset circuit breaker.

Oven controls improperly set.

• See the Using the oven section.

On self-cleaning models, door left in the locked position.

• If necessary, allow the oven to cool then unlock the door.

Oven controls improperly set.

•See the Using the oven section.

Shelf position is incorrect or the shelf is not level.

• See the Using the oven section.

Incorrect cookware or cookware of improper size being used.

• See the Using the oven section.

Oven thermostat needs adjustment.

•See the Adjust the oven thermostat–Easy to do yourself! section.

Possible Causes

What To Do

Food does not broil properly

Oven is not set to BROIL.

•On models with a temperature knob, make sure you turn it all the way to the BROIL position. On models with a BROIL HI/LO pad, make sure it is turned on.

Door not open to the broil stop position as recommended.

•See the Using the oven section.

Improper shelf position being used.

• See the Broiling guide.

Food being cooked in a hot pan.

• Use the broiling pan and grid that came with your range. Make sure it is cool.

• See the Using the oven section.

In some areas the power (voltage) may be low.

• Preheat the broil element for 10 minutes. • Broil for the longest period of time recommended in the Broiling guide.

Control signals after entering cooking time or delay start

You forgot to enter a bake temperature or cleaning time.

•Press the BAKE pad and desired temperature or the SELF CLEAN pad and desired clean time.

Display flashes "bAd" then "linE" with a loud tone

The installed connection from the house to the unit is miswired.

•Contact installer or electrician to correct miswire.

Installation Instructions

Aluminum foil used on the broiling pan and grid has not been fitted properly and slit as recommended.

Care and Cleaning

Cookware not suited for broiling. • Use the broiling pan and grid that came with your range.

Operating Instructions

Problem

Safety Instructions

www.AmericanaAppliances.com

Troubleshooting Tips Consumer Support

41

Safety Instructions Operating Instructions Care and Cleaning Installation Instructions Consumer Support Troubleshooting Tips

Before you call for service… Troubleshooting Tips

Problem

Possible Causes

What To Do

Oven temperature too hot or too cold

Oven thermostat needs adjustment.

•See the Adjust the oven thermostat–Easy to do yourself! section.

Clock and timer do not work

Plug on range is not completely inserted in the electrical outlet.

• Make sure electrical plug is plugged into a live, properly grounded outlet.

A fuse in your home may be blown or the circuit breaker tripped.

• Replace fuse or reset circuit breaker.

Oven controls improperly set.

•See the Using the clock and timer section.

A fuse in your home may be blown or the circuit breaker tripped.

• Replace the fuse or reset the circuit breaker.

The clock is turned off from showing in the display.

• See the Using the clock and timer section.

Oven door is crooked

The door is out of position.

• Because the oven door is removable, it sometimes gets out of position during installation. To straighten the door, push down on the high corner.

Oven makes clicking noise

This is the sound of the heating element turning off and on during cooking functions.

•This is normal.

“F—and a number or letter” flash in the display

You have a function error code.

• Press the CLEAR/OFF pad. Put the oven back into operation.

If the function code repeats:

• Disconnect all power to the range for at least 30 seconds and then reconnect power. If the function error code repeats, call for service.

Display goes blank

• On self-cleaning models, if a function error code appears during the self-cleaning cycle, check the oven door latch. The latch may have been moved, if only slightly, from the locked position. Make sure the latch is moved to the right as far as it will go. Press the CLEAR/OFF pad. Allow the oven to cool for one hour. Put the oven back into operation. Power outage

Power outage or surge.

•Some models will automatically resume their setting once the power is restored. On models with a clock, you must reset the clock. If the oven was in use, you must reset it by pressing the CLEAR/OFF pad, setting the clock and resetting any cooking function.

Display flashes

Power failure.

•Reset the clock.

Unable to get the display to show “SF”

Oven control pads were not pressed properly.

•The BAKE and BROIL HI/LO pads must be pressed at the same time and held for 3 seconds.

42

Possible Causes

What To Do

“Burning” or “oily” odor emitting from the oven vent

This is normal in a new oven and will disappear in time.

• To speed the process, set a self-clean cycle for a minimum of 3 hours. See the Using the self-cleaning oven section.

Strong odor

An odor from the insulation around the inside of the oven is normal for the first few times the oven is used.

• This is temporary.

Operating Instructions

Problem

Safety Instructions

www.AmericanaAppliances.com

Self-Cleaning Models The oven temperature is too • Allow the range to cool to room temperature and high to set a self-clean operation. reset the controls. • See the Using the self-cleaning oven section.

Oven door is not in the locked position.

• Make sure you move the door latch handle all the way to the right.

Oven starts a self-clean cycle when you wanted to bake, roast or broil

Oven door locked during cooking.

• Turn the Oven Temperature knob to OFF. Allow the oven to cool. Never force the door latch handle.

“Crackling” or “popping” sound

This is the sound of the metal • This is normal. heating and cooling during both the cooking and cleaning functions.

Excessive smoking during a clean cycle

Excessive soil.

•Press the CLEAR/OFF pad. Open the windows to rid the room of smoke. Wait until the light on the SELF CLEAN pad goes off. Wipe up the excess soil and reset the clean cycle.

Oven door will not unlock

Oven too hot.

•Allow the oven to cool below locking temperature.

Oven not clean after a clean cycle

Oven controls not properly set.

•See Using the self-cleaning oven section.

Oven was heavily soiled.

•Clean up heavy spillovers before starting the clean cycle. Heavily soiled ovens may need to self-clean again or for a longer period of time.

Installation Instructions

Oven controls improperly set.

Care and Cleaning

Oven will not self-clean

Troubleshooting Tips Consumer Support

43

Looking For Something More? You can find these accessories and many more by calling 800.626.2002 (during normal business hours). Have your model number ready.

Surface Elements & Drip Pans

Oven Racks

Broiler Pan

Oven Elements

Light Bulbs

Knobs

Cleaner

Cleaning Pads

Scraper

Consumer Support Troubleshooting Tips

Installation Instructions

Care and Cleaning

Operating Instructions

Safety Instructions

Accessories.

Tired of discolored racks? Wishing you had extra-heavy-duty oven racks?

NOW AVAILABLE for your range: New innovative porcelain-coated oven racks! • Heavy Duty • Durable • Able to be cleaned in a self-cleaning oven (on models so equipped)

44

GE Service Protection Plus™ GE, a name recognized worldwide for quality and dependability, offers you Service Protection Plus ™---comprehensive protection on all your appliances--No Matter What Brand! Benefits Include: • Backed by GE • All brands covered • Unlimited service calls • All parts and labor costs included • No out-of-pocket expenses • No hidden deductibles • One 800 number to call

We’ll Cover Any Appliance. Anywhere. Anytime.*

You will be completely satisfied with our service protection or you may request your money back on the remaining value of your contract. No questions asked. It’s that simple. Protect your refrigerator, dishwasher, washer and dryer, range, TV, VCR and much more---any brand! Plus there’s no extra charge for emergency service and low monthly financing is available. Even icemaker coverage and food spoilage protection is offered. You can rest easy, knowing that all your valuable household products are protected against expensive repairs. Place your confidence in GE and call us in the U.S. toll-free at 800.626.2224 for more information. *All brands covered, up to 20 years old, in the continental U.S.



Cut here

Please place in envelope and mail to:

General Electric Company Warranty Registration Department P.O. Box 34980 Louisville, KY 40232-4980

45

Consumer Product Ownership Registration Dear Customer: Thank you for purchasing our product. Registration for Americana™ is provided by GE. Thank you for placing your confidence in us. We are proud to have you as a customer!

Follow these three steps to protect your new appliance investment:

1 2 3 Complete and mail your Consumer Product Ownership Registration today. Have the peace of mind of knowing we can contact you in the unlikely event of a safety modification.

After mailing the registration below, store this document in a safe place. It contains information you will need should you require service. Our service number is 800.432.2737.

Model Number

Read your Owner’s Manual carefully. It will help you operate your new appliance properly.

Serial Number

Important: If you did not get a registration card with your product, detach and return the form below to ensure that your product is registered.



Cut here

Consumer Product Ownership Registration Model Number

ant ort l p Im Mai ay! d To Mr. ■

Ms. ■

Mrs. ■

Serial Number

Miss ■

First Name

Last Name

Street Address

Apt. #

E-mail Address*

Date Placed In Use

Month

Day

GE Consumer & Industrial Appliances General Electric Company Louisville, KY 40225 ge.com

46

Zip Code

State

City

Year

Phone Number

_

_

* Please provide your e-mail address to receive, via e-mail, discounts, special offers and other important communications from GE Appliances (GEA). ■ Check here if you do not want to receive communications from GEA’s carefully selected partners. FAILURE TO COMPLETE AND RETURN THIS CARD DOES NOT DIMINISH YOUR WARRANTY RIGHTS. For information about GEA’s privacy and data usage policy, go to ge.com and click on “Privacy Policy” or call 800.626.2224.

www.AmericanaAppliances.com

Safety Instructions

Electric Range Warranty. All warranty services for Americana™ are provided by GE Factory Service Centers, or an authorized Customer Care® technician. To schedule service, call 800.432.2737. Please have serial number and model number available when calling for service.

Staple your receipt here. Proof of the original purchase date is needed to obtain service under the warranty.

We Will Provide:

One Year From the date of the original purchase

Any part of the range which fails due to a defect in materials or workmanship. During this limited one-year warranty, we will also provide, free of charge, all labor and in-home service to replace the defective part.

What Is Not Covered: ■ Products which are not defective, broken, or which are working as described in the Owner’s Manual.

■ Improper installation, delivery or maintenance.

■ Replacement of house fuses or resetting of circuit breakers.

■ Failure of the product if it is abused, misused, or used for other than the intended purpose or used commercially. ■ Damage to the glass cooktop caused by use of cleaners other than the recommended cleaning creams. ■ Damage to the glass cooktop caused by hardened spills of sugary materials or melted plastic that are not cleaned according to the directions in the Owner’s Manual.

■ Damage to the product caused by accident, fire, floods or acts of God. ■ Incidental or consequential damage caused by possible defects with this appliance. ■ Damage caused after delivery. ■ Product not accessible to provide required service.

Some states do not allow the exclusion or limitation of incidental or consequential damages. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. To know what your legal rights are, consult your local or state consumer affairs office or your state’s Attorney General.

Warrantor: General Electric Company. Louisville, KY 40225

47

Troubleshooting Tips Consumer Support

This warranty is extended to the original purchaser and any succeeding owner for products purchased for home use within the USA. If the product is located in an area where service by a GE Authorized Servicer is not available, you may be responsible for a trip charge or you may be required to bring the product to an Authorized GE Service location for service. In Alaska, the warranty excludes the cost of shipping or service calls to your home.

Installation Instructions

EXCLUSION OF IMPLIED WARRANTIES—Your sole and exclusive remedy is product repair as provided in this Limited Warranty. Any implied warranties, including the implied warranties of merchantability or fitness for a particular purpose, are limited to one year or the shortest period allowed by law.

Care and Cleaning

■ Service trips to your home to teach you how to use the product.

Operating Instructions

For The Period Of:

Consumer Support. Schedule Service Expert GE repair service is only one step away from your door. Schedule service at your convenience by calling 800.432.2737 during normal business hours. In Canada, call 1.800.361.3400

Extended Warranties Purchase a GE extended warranty and learn about special discounts that are available while your warranty is still in effect. You can purchase it by calling 800.626.2224 during normal business hours. GE Consumer Home Services will still be there after your warranty expires. In Canada, call 1.888.261.2133

Parts and Accessories Individuals qualified to service their own appliances can have parts or accessories sent directly to their homes (VISA, MasterCard and Discover cards are accepted). Order by phone at 800.626.2002 during normal business hours. Instructions contained in this manual cover procedures to be performed by any user. Other servicing generally should be referred to qualified service personnel. Caution must be exercised, since improper servicing may cause unsafe operation. Customers in Canada should consult the yellow pages for the nearest Camco service center, or call 1.888.261.3055.

Contact Us

www.AmericanaAppliances.com

If you are not satisfied with the service you receive from GE, send a letter to GE. Please include your phone number. Write to: General Manager, Customer Relations GE Appliances, Appliance Park Louisville, KY 40225 In Canada:

Write to:

Director, Consumer Relations, Camco, Inc. Suite 310, 1 Factory Lane Moncton, N.B. E1C 9M3

Printed in Mexico Printed on Recycled Paper