Jun 29, 2006 - 1-800-843-6849 ... HITCH JACK, 15" SIDE WIND (232-800) . ..... 450-050. Winch, 1600 lb., 5.1:1 ratio. 1.
TWR-180 TWR-120 ROTARY CUTTER Published 2006-06-29
Serial #C31400382705-C31400552806 Inclusive Serial #C31500030705-C31500039806 Inclusive
Part No. C314TG010P
PARTS MANUAL An Operators Manual with IMPORTANT Safety, Assembly, Operation and Maintenance information was packaged with this Parts Manual during final inspection at the factory. If the Operators Manual is missing at any time, please contact Tiger Corporation to receive your free replacement manual.
Tiger Corporation 3301 N. Louise Ave. Sioux Falls, SD 57107 1-800-843-6849 1-605-336-7900 www.tiger-mowers.com © 2006 Alamo Group Inc.
PARTS ORDERING GUIDE The following instructions are offered to help eliminate delay and error in processing purchase orders for the equipment in this section. 1. The Purchase Order must include the name and address of the person or organization ordering the parts, who should be charged, and if possible, the serial number of the machine for which the parts were ordered. 2. The Purchase Order must clearly list the quantity of each part, the complete and correct part number, and the description of the part. 3. The Manufacturer reserves the right to substitute parts where applicable. 4. The Manufacturer reserves the right to change prices without prior notice. NOTE:
Please refer to the Safety Section in the front of the Operators Manual for the proper Part Number when ordering Replacement Safety Decals. Safety decals are available free of charge from the Manufacturer.
NOTE:
If the Operators Manual does not accompany this Parts Manual please obtain one, free of charge from the Manufacturer. DO NOT operate this implement unless you READ, UNDERSTAND, and FOLLOW the Safety and Operation instructions contained in the Operators Manual
NOTE:
Please note that the appearance of some parts may vary from the artwork shown in the Manual. For maximum safety and to guarantee optimum product reliability, always use genuine OEM Parts. The use of inferior replacement parts may cause premature or catastrophic failure which could result in serious injury or death. Direct any questions regarding parts to:
Tiger Corporation 3301 N. Louise Ave. Sioux Falls, SD 57107 1-800-843-6849 1-605-336-7900 www.tiger-mowers.com
-1-
TABLE OF CONTENTS CENTER SECTION FRAME . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -3WING FRAME, RIGHT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -5WING FRAME, LEFT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -7HITCH FRAME AND CENTER WHEEL STANDARD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -910' SKIRT ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -11HITCH JACK, 15" SIDE WIND (232-800) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -12HUB, AXLES & TIRES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -13DRIVELINE SHIELDING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -15CHAIN GUARDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -17BLADE CARRIERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -19WING WINCH KIT (C312-300) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -21WING LIFT CIRCUIT, SINGLE ACTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -22WING LIFT CYLINDER, MONARCH (100-3701) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -23PHASING CIRCUIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -24PHASING CYLINDERS, MONARCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -25SPOOL VALVE KIT, S150 (C301-805) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -26SPOOL VALVE KIT, S100 (C302-805) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -28TRACTOR UNIVERSAL JOINT W/ 80o C.V., SIZE 8 (340-850) . . . . . . . . . . . . . . . . . . . . . . -29TRACTOR UNIVERSAL JOINT W/ 80o C.V., SIZE 6 (340-648) . . . . . . . . . . . . . . . . . . . . . . -31WING UNIVERSAL JOINT, SIZE 6 (340-6013) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -33CENTER UNIVERSAL JOINT, SIZE 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -35SLIP CLUTCH (341-6322, 341-6323) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -36SLIP CLUTCH (341-6324) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -38DIVIDER GEARBOX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -39CW GEARBOX, WING (330-7030) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -41CCW GEARBOX, WING (330-7031) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -43CW GEARBOX, CENTER, 540 RPM (330-7035) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -45CW GEARBOX, CENTER, 1000 RPM (330-7036) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -47TRANSPORT KITS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -49PARTS INDEX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -50-
-2-
CENTER SECTION FRAME
June 27, 2006
-3-
CENTER SECTION FRAME
Ref. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
Part No. Description Qty. C314-101 Center section assembly 1 228-012 Hose organizer 2 250-112 Bolt, 3/4 x 3 UNC 6 270-004 Lock nut, 5/8 UNC 10 250-093 Bolt, 5/8 x 1-3/4 UNC 2 256-006 Flat washer, 5/8 2 C310-112 Skid mount assembly 2 250-084 Bolt, 5/8 x 4-1/2 UNC 4 C301-113 Wing lift spacer plate 2 250-060 Bolt, ½ x 1-3/4 UNC 3 C310-144 Retainer pin, 1 x 5-3/16 U.L 1 256-011 Flat washer, 1/2 3 270-007 Lock nut, 1/2 UNC 3 256-001 Flat washer, 1 3 262-006 Roll pin, 3/8 x 2 3 C310-143 Retainer pin, 1 x 2-3/4 U.L. 2 250-112 Bolt, 3/4 x 3 UNC (light truck tire) 2 250-111 Bolt, 3/4 x 4 UNC (laminated & aircraft) 2 18 C310-105 Cylinder lug adjustment assembly. 1 19 C310-120 Spacer plate, 1" (light truck tire) 1 C310-120 Spacer plate, 1" (laminated & aircraft tire) 2 * See “Fixed Knife Shredder Kit” parts page for additional spacer plates required * See “Sod Kit” parts page for special spacer plate requirements 20 C301-118 Wing lock pin, 1 x 5-9/16 U.L. 2 21 250-023 Bolt, 3/8 x 1-3/4 UNC 5 22 256-017 Flat washer, 3/8 4 23 300-012 Lynch pin, 1/4 3 24 C312-119 Slow moving vehicle sign stand 1 25 270-017 Lock nut, 3/8 UNC 8 26 250-019 Bolt, 3/8 x 1-1/4 UNC 2 27 270-001 Lock nut, 3/4 UNC 8 28 C310-115 Bolt access cover plate 1 29 255-013 Lock washer, 3/8 2 30 250-018 Bolt, 3/8 x 1 UNC 4 31 330-7035 Gear box, 540 RPM 1 330-7036 Gear box, 1000 RPM 1 33 150-32 Complete, SMV sign 1 34 330-930 Splitter box, 540 RPM 1 330-931 Splitter box, 1000 RPM 1 35 250-090 Bolt, 5/8 x 2 UNC 4 36 C310-127 Transport lock pin, 1 x 5-5/16 U.L. 1 37 280-200 Manual Box 1 38 256-018 Washer, 1/4" 2 39 250-002 Bolt, 1/4" x 1" UNC 2 40 270-025 Locknut, 1/4" UNC 2 41 C000-001 Hose clamp 1 42 262-005 Roll Pin, 3/8 x 2-1/2" 1
June 27, 2006
-4-
WING FRAME, RIGHT
June 27, 2006
-5-
WING FRAME, RIGHT
Ref. Part No. Description Qty. 1 C314-155 Wing assembly, right 1 2 752-014 Hinge pin, 15" O.A. 4 3 C310-140 Hinge spacer tube, 13-7/8" O.A. 2 5 262-011 Roll Pin, 3/8 x 1-3/4 6 6 C310-141 Hinge spacer tube, 10-3/8" O.A. 1 7 262-006 Roll pin, 3/8 x 2 5 8 256-001 Flat washer, 1 6 9 C301-140 Pin, 1 x 3-13/32" O.A. 2 10 C301-114 Floating lug 2 13 330-7031 Gearbox, CCW 1 * CW Gearbox (330-7030) is required for fixed knife, material distribution, and sod kits. See your Schulte Dealer 14 250-201 Plow bolt, ½ x 1-1/2 UNC 3 16 C310-135 Outer wing skid, standard 1 17 270-007 Lock nut, ½ UNC 10 18 256-011 Flat washer, 1/2 4 19 255-020 Lock washer, 1-1/4" 1 20 257-054 Half nut, 1-1/4" UNC 2 21 C310-145 Retainer pin, 1 x 6-15/16 U.L. 1 22 250-059 Bolt, ½ x 1-1/2 UNC 1 23 302-015 Clevis pin, 1 x 2-7/8 1 24 250-111 Bolt, 3/4 x 4 UNC 1 25 C310-124 Wheel standard suspension plate 1 26 233-050 Rubber sandwich 1 27 C310-123 Wing wheel standard assembly 1 28 270-001 Lock nut, 3/4 UNC 9 29 250-112 Bolt, 3/4 x 3 UNC 8 30 271-005 Cotter pin, 3/16 x 1-1/2 1 31 273-006 Grease nipple, self tap 1 32 C310-115 Bolt access cover plate 1 33 255-013 Lock washer, 3/8 2 34 250-018 Bolt, 3/8 x 1 UNC 2 35 C320-132 Wing adjustment assembly 1 36 250-055 Bolt, ½ x 3/4 UNF 2 37 250-061 Bolt, ½ x 1-1/4 UNC 6 38 C312-157 Adjustable side mount, right 1
June 27, 2006
-6-
WING FRAME, LEFT
June 27, 2006
-7-
WING FRAME, LEFT
Ref. Part No. Description Qty. 1 C314-150 Wing assembly, left 1 2 752-014 Hinge pin, 15" O.A. 4 3 C310-140 Hinge spacer tube, 13-7/8" O.A. 2 5 262-011 Roll Pin, 3/8 x 1-3/4 6 6 C310-141 Hinge spacer tube, 10-3/8" O.A. 1 7 262-006 Roll pin, 3/8 x 2 5 8 256-001 Flat washer, 1 6 9 C301-140 Pin, 1 x 3-13/32" O.A. 2 10 C301-114 Floating lug 2 13 330-7030 Gearbox, CW 1 * CCW Gearbox (330-7031) is required for fixed knife, material distribution, and sod kits. See your Schulte Dealer 14 250-201 Plow bolt, ½ x 1-1/2 UNC 3 16 C310-135 Outer wing skid, standard 1 17 270-007 Lock nut, ½ UNC 10 18 256-011 Flat washer, ½ 4 19 255-020 Lock washer, 1-1/4" 1 20 257-054 Half nut, 1-1/4" UNC 2 21 C310-145 Retainer pin, 1 x 6-15/16 U.L. 1 22 250-059 Bolt, ½ x 1-1/2 UNC 1 23 302-015 Clevis pin, 1 x 2-7/8 1 24 250-111 Bolt, 3/4 x 4 UNC 1 25 C310-124 Wheel standard suspension plate 1 26 233-050 Rubber sandwich 1 27 C310-123 Wing wheel standard assembly 1 28 270-001 Lock nut, 3/4 UNC 9 29 250-112 Bolt, 3/4 x 3 UNC 8 30 271-005 Cotter pin, 3/16 x 1-1/2 1 31 273-006 Grease nipple, self tap 1 32 C310-115 Bolt access cover plate 1 33 255-013 Lock washer, 3/8 2 34 250-018 Bolt, 3/8 x 1 UNC 2 35 C320-132 Wing adjustment assembly 2 36 250-055 Bolt, ½ x 3/4 UNF 2 37 250-061 Bolt, ½ x 1-1/4 UNC 6 38 C312-152 Adjustable skid mount, left 1
June 27, 2006
-8-
HITCH FRAME AND CENTER WHEEL STANDARD
June 27, 2006
-9-
HITCH FRAME AND CENTER WHEEL STANDARD
Ref. 1 2 3 4 5 7 8 9 10 11 12 13 14 16 17 18 19 20 21 22 23 24 25 28 29 30 31 32 33
June 27, 2006
Part No. 271-005 256-001 302-013 262-006 C310-113 C310-118 C310-119 250-060 256-011 270-007 273-006 C310-117 C310-142 C310-131 302-015 229-007 250-111 C310-125 270-001 CS01-130 257-008 257-006 302-012 C310-108 250-112 CS01-134 C502-183 302-034 271-053
Description Cotter pin, 3/16 x 1-1/2 Flat washer, 1 Clevis pin, 1 x 2-1/8 Roll pin, 3/8 x 2 Hitch clevis Pivoting hitch assembly. Pivot hitch weld sleeve Bolt, 1/2 x 1-3/4 UNC Flat washer, 1/2 Lock nut, 1/2, UNC Grease nipple, self tap Hitch frame assembly Retaining pin, 1 x 3-15/16 U.L. Lift rod, 101" O.A. Clevis pin, 1 x 2-7/8 Compression spring, 1/2” Bolt, 3/4 x 4 UNC Suspension top plate Lock nut, 3/4 UNC Leveling rod lug Nut, 1 UNC Half nut, 1 UNC Clevis pin, 1 x 1-15/16 Center section wheel standard Bolt, 3/4 x 3 UNC Retaining pin, 1 x 4-5/8 U.L. PTO storage support Bent hitch pin #10 hitch pin clip
-10-
Qty. 3 13 2 3 1 1 1 3 7 3 6 1 2 2 1 2 1 1 5 2 2 2 2 1 4 1 1 1 1
10' SKIRT ASSEMBLY
Ref. 1 2 3 4 5 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23
June 27, 2006
Part No. 250-060 250-059 256-011 C311-105 C311-106 250-145 270-007 C311-102 270-020 C311-101 C311-103 C302-104 256-001 250-129 250-201 C302-106 270-017 225-106 225-111 250-085 256-017 256-006 250-020 270-004
Description Bolt, 1/2" x 1-3/4" UNC Bolt, 1/2" x 1-1/2" UNC Flat washer, 1/2" Chain guard, single Chain guard, double Bolt, 1" x 4" UNC Lock nut, 1/2" UNC Hinge pin, 29 1/8" O.A. Lock nut, 1" UNC Skirt assembly, 10' Hinge pin, 5" O.A. Counter weight Flat washer, 1" Bolt, 1" x 6" UNC Plow bolt, 1/2" x 1-1/2" UNC Skirt skid Lock nut, 3/8" UNC Chain, 5/16" proof coil, 6 links Chain, 5/16" proof coil, 11 links Bolt, 5/8" x 4" UNC Flat washer, 3/8" Flat washer, 5/8" Bolt, 3/8" x 1-1/2" UNC Lock nut, 5/8" UNC
-11-
Qty. 2 2 9 1 1 2 9 1 4 1 1 3 4 2 5 1 3 3 3 4 3 4 3 4
HITCH JACK, 15" SIDE WIND (232-800)
Ref. 1 2 10 11 12 13 14 16 20
Part No. 232-621 232-622 232-623 232-624 232-625 232-626 232-627 232-628 232-630
Description Outer Tube and Mount Inner Tube/ S&N Assembly Crank, Handle Cover Bolt,1/4-20 x 3.12" Carriage Locknut, 1/4" Pull Pin Assembly Grease Fitting Repair Kit, c/w Ref # 3 to 9
NOTE: THIS JACK WILL REPLACE JACK 232-600
June 27, 2006
-12-
Qty. 1 1 1 1 2 2 1 1 1
HUB, AXLES & TIRES
When attaching the wheels to the hub, be sure the lock washer is installed agianst the wheel. To reduce the possibility of the laminations separating, the laminated tires should be installed with the laminations oriented as shown above.
June 27, 2006
-13-
HUB, AXLES & TIRES
Ref. 1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 17 18 19 20 21 22 23 23 24 25 26
June 27, 2006
Part No. 208-018 208-019 207-026 207-019 207-020 273-006 205-007 207-025 207-024 271-005 201-005 201-010 211-002 210-167 210-157 207-0281 207-027 209-017 250-018 210-003 255-013 257-032 201-008 210-004 206-009 207-055 210-162 211-010 255-009 250-0612
Description Spindle, c/w #9, 15, 16, double end Spindle, c/w #9, 15, 16, single end Seal Bearing Race Grease nipple, self-tap Hub, c/w outer races Race Bearing Cotter pin, 3/16 x 1-1/2 Wheel, 15 x 5 KB, 5 bolt, For 7.00 Tire Wheel, 15 x 8 x 5, For 9.5L Tire Valve stem Tire, 7.00 x 15, 8 ply Tire, 9.5L x 15 Wheel bolt, 1/2-20 UNF x 1" wide shoulder Dust cap Castle nut, 3/4 - 16 UNF Bolt, 3/8 x 1 UNC Tire, solid laminated, complete Lock washer, 3/8" Nut, 3/8 UNC Wheel half, 6 x 9, 5 bolt Tire, solid laminated, 6 x 9 Hub, includes #2-8 & 14 Bearing Kit, includes #2, 3, 4, 7, 8, 14, 16 Aircraft tire 22 x 5.5 x 10 complete Tube & liner for #210-162 Lock washer, 1/2 Bolt, 1/2 x 1-1/4 UNF Gr. 5
-14-
Qty. 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 5 1 1 5 1 5 5 2 1 1 1 1 5 5
DRIVELINE SHIELDING
June 27, 2006
-15-
DRIVELINE SHIELDING
Ref. 1 3 4 5 6 11 12 13 14 15 16 25 26 27 28 29 30
June 27, 2006
Part No. C314-203 251-008 255-015 256-020 C314-202 341-6235 C314-204 341-600 250-006 271-008 C301-203 251-151 270-028 C314-205 227-001 227-002 271-013
Description Center section shield assembly CE Bolt, M8 x 20mm Lock washer, 5/16" Flat washer, 5/16" Splitter shield mount Plastic shield Center gearbox pivot shield mount Plastic shaft cover for splitter, 10' units Bolt, 5/16" x 3/4" UNC, 10' units Cotter pin, 1/8" x 1" Shield hinge pin Machine Screw #10 x .75" Round Head Locknut, 10-24 Nylock Spacer CE Shield Latch Euro Lock Key, 10 Ga Stainless Steel Cotter Pin, 1/16" x 3/4" long (Not for CE)
-16-
Qty. 1 15 15 15 1 2 1 1 2 2 1 2 2 1 1 1 1
CHAIN GUARDS
June 27, 2006
-17-
CHAIN GUARDS
C310-550
Double Chain Guard Kit, S150
Ref. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Part No. C310-555 C310-552 C310-551 C310-554 C310-557 C310-558 250-026 256-017 270-017 225-109 250-050 250-061 256-011 270-007 250-059
C310-520
Cable Kit for Double Chains, S150
Ref. 17 18 19 20 21 22
Part No. 221-413 221-415 221-416 221-414 221-417 222-003
June 27, 2006
Description Chain guard double, wing front Chain guard double, center front outer Chain guard double, center front middle Chain guard double, center rear Chain guard double, wing rear Chain guard double, wing rear outer Bolt, 3/8" x 2-1/2" UNC Flat washer, 3/8" Lock nut, 3/8" UNC Chain, 5/16" proof coil, 9 links Bolt, 1/2" x 3-1/2" UNC Bolt, 1/2" x 1-1/4" UNC Flat washer, 1/2" Lock nut, 1/2" UNC Bolt, 1/2" x 1-1/2"
Description Cable, 73" Cable, 26-3/4" Cable, 22" Cable, 75-1/4" Cable, 62" Cable clamp, 1/8"
-18-
Qty. 4 2 1 2 4 2 2 4 2 4 12 21 63 51 18
Qty. 2 2 1 2 1 16
BLADE CARRIERS
June 27, 2006
-19-
BLADE CARRIERS
Ref. 1 2 3 4 6 7 8 9 10 11 13
Part No. C303-222 C303-220 520-1076 520-1075 586-535 251-020 257-003 401-026 401-027 401-032 251-018 251-201
Description Blade carrier, center, complete Blade carrier, wing, complete Pan only, center Pan only, wing Pan reinforcements, center Pentagon bushing, blade bolt Locknut, 1-1/8 - 12, UNF Blade,1/2 x 4 x 25, CW, Super Suction Blade,1/2 x 4 x 25, CCW, Super Suction Blade, 1/2 x 4 x 28, CW, Super Suction Blade bolt, 1-1/8 - 12 UNF, 1/2" Blade bolt & nut, 1/2"
.
June 27, 2006
-20-
Qty. 1 2 1 2 4 6 6 2 2 2 6 6
WING WINCH KIT (C312-300)
Ref. 1 2 3 4 5 6 7 8 9 10 11 12 13 June 27, 2006
Part No. 450-050 250-019 256-017 158-03 270-017 C310-302 C312-302 C312-301 C301-303 250-061 270-007 250-018 450-104
Description Winch, 1600 lb., 5.1:1 ratio Bolt, 3/8 x 1-1/4 UNC Flat washer, 3/8 Cable, 135", 7/32 dia. 1/4 loop end Lock nut, 3/8 UNC Winch lift stand Winch lift lug, right Winch lift lug, left Backing plate Bolt, ½ x 1-1/4 UNC Lock nut, ½ UNC Bolt, 3/8 x 1 UNC Winch cable keeper, hardware included -21-
Qty. 1 3 3 1 5 1 1 1 1 4 4 2 1
WING LIFT CIRCUIT, SINGLE ACTING
C310-820
Single Acting Wing Cylinder Kit Includes Ref # 2 only.
Ref. 1 2 3 4 5 8 9 10
Part No. 100-3701 108-056 108-043 111-185 C000-005 302-015 256-001 271-005
June 27, 2006
Description Cyl. 3 X 12 ORB Breather, filter 3/4- 16 ORB Elbow, 3/4" ORB male X JIC male Hose assembly, 3/8 SW, 183" long Restrictor Clevis pin, 1 x 2-7/8 UL Flat washer, 1 x 2 Cotter pin, 3/16 x 1-1/2
-22-
Qty. 2 2 2 2 2 2 2 2
WING LIFT CYLINDER, MONARCH (100-3701)
Ref. 1 2 3 4 25 41
June 27, 2006
Part No. 101-150 101-151 101-152 101-153 101-243 101-025W
Description Casing, 3" x 12" Cylinder Head Piston Rod Lock Nut, 1" Seal Kit, Includes # 10, 11, 13-15, 40
-23-
Qty. 1 1 1 1 1 1
PHASING CIRCUIT
Ref. 1 2 3 4 7 8 9 10 11 13 14 17 18 19 20 21 22 23 24 25 26
June 27, 2006
Part No. 111-101 100-3671 111-188 C000-001 108-043 100-3681 111-186 100-3691 111-184 271-005 302-015 250-023 256-017 270-017 108-044 101-020 C000-005 262-006 C502-193 C502-194 256-001
Description Hose assembly, 3/8 x 191" long Cylinder phasing, 3-1/2 x 5 Hose assembly, 3/8 x 84" long Hose clamp, metal Elbow, 3/4 ORB male x JIC male Cylinder phasing, 3-1/4 x 5 Hose assembly, 3/8 x 171" long Cyl. phasing, 3 x 5 Hose assembly, 3/8 x 269" long Cotter pin, 3/16 x 1-1/2 Clevis pin, 1 x 2-7/8 U.L. Bolt, 3/8 x 1-3/4 UNC Flat washer, 3/8 Locknut, 3/8 UNC Elbow, 450 ORB x JIC Depth stop Restrictor Roll pin, 3/8" x 2 Center section cylinder pin Cylinder pin sleeve Washer, 1"
-24-
Qty. 1 1 1 4 5 1 1 1 1 6 6 1 3 3 1 3 1 1 1 1 5
PHASING CYLINDERS, MONARCH
Ref. 1 2 3 4 5 17 18 20 21 25 41
June 27, 2006
3" Part No. 100-3691 101-145 101-137 101-082 101-148 257-055 101-021 250-023 270-017 101-020 101-243 101-065
3-1/4" Part No. 100-3681 101-146 101-138 101-083 101-148 257-055 101-021 250-023 270-017 101-020 101-243 101-066
3-1/2" Part No. 100-3671 101-147 101-139 101-084 101-148 257-055 101-021 250-023 270-017 101-020 101-243 101-067
Description Phasing Cylinder Casing Cylinder Head Piston Rod Jam nut, 1-1/4" UNF Rod Clevis Bolt, 3/8" x1-3/4" UNC, Gr 5 Lock Nut, 3/8" UNC Stroke Control Assembly Lock Nut, 1" Seal Kit, Incl #10,11,13-15,40
-25-
Qty. 1 1 1 1 1 1 1 1 1 1 1
SPOOL VALVE KIT, S150 (C301-805)
Ref. 1 2 3 4 5 6 7 8 9 10 11
June 27, 2006
Part No. 108-044 108-068 108-031 108-043 111-204 111-205 111-206 111-207 111-237 127-202 108-0071
Description Elbow, 3/4 ORB x 3/4 JIC Reducer, 3/4 ORB x ½ NPTF Elbow, 3/4 - 16 JIC Elbow, 3/4 ORB x 3/4 JIC Hose assembly, 3/8 x 226" long Hose assembly, 3/8 x 329" long Hose assembly, 3/8 x 243" long Hose assembly, ½ x 60" long Hose assembly, ½ x 72" long Valve, 3 spool Brass restrictor
-26-
Qty. 6 1 1 3 1 1 4 1 1 1 3
June 27, 2006
-27-
SPOOL VALVE KIT, S100 (C302-805)
Ref. 1 2 3 4 5 6 7 8 9 10 11
June 27, 2006
Part No. 108-003 108-018 108-031 108-043 111-204 111-205 111-206 111-207 111-237 127-201 108-0071
Description Elbow, 1/2 NPT x 3/4 JIC Reducer, 3/4 NPTM x ½ NPTF Elbow, 3/4 - 16 JIC Elbow, 3/4 ORB x 3/4 JIC Hose assembly, 3/8 x 226" long Hose assembly, 3/8 x 329" long Hose assembly, 3/8 x 243" long Hose assembly, ½ x 60" long Hose assembly, ½ x 72" long Valve, 2 spool Brass restrictor
-28-
Qty. 5 2 1 2 1 1 2 1 1 1 2
TRACTOR UNIVERSAL JOINT W/ 80o C.V., SIZE 8 (340-850)
June 27, 2006
-29-
TRACTOR UNIVERSAL JOINT W/ 80o C.V., SIZE 8 (340-850)
Location: 540 RPM units Ref. 1 2 5 6 8 12 13 16 17 21 22 23 25 26 27 28 29 30 31 32 34 51 61 93 94 97
June 27, 2006
Part No. 341-80046 341-80047 341-80048 341-80045 341-80074 341-80055 341-80056 341-80007 341-80008 341-80070 341-80002 341-8086 341-80049 341-60039 341-80050 341-60020 341-80057 341-80058 341-80059 341-60014 341-80069 341-8095 341-802 341-80061 341-80062 341-80067
Description Yoke, 1-3/8 z6 Cross Kit Yoke, Outer Tube Central Body Flexible Pin Outer Cardan Tube Inner Cardan Tube Flexible Pin Yoke, Inner Tube Yoke, 1-3/4 z20 Cross Kit Grease Fitting, Short Bell Assembly Shield Bearing, Outer Ring Screw Outer Bell & Tube Inner Bell & Tube Shield Shield Bearing, Inner Washer Ball Collar Kit Tapered Pin Kit Tractor Half Assembly w/ Shields, 1-3/8 z6 Implement Half Assembly w/Shields Complete Shield Set
-30-
Qty. 1 2 1 1 1 1 1 1 1 1 1 2 1 1 1 12 1 1 1 1 6 1 1 1 1 1
'5,9(/,1(
94
61
22 16 13 21 23 93
17
8
28
2
31
6 32
12 2
5
1
40
28
30
28 34 29 51
97
40 26 25 27
&3 $ODPR *URXS ,QF
3DJH31
'5,9(/,1(
127( 530 &9 7UDFWRU $VVHPEO\ 5HI
3DUW 1R
&3 $ODPR *URXS ,QF
4W\
'HVFULSWLRQ
